found this under the valve cover...

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 1, 2004
Threads
237
Messages
1,677
Location
Iowa
I pulled off the valve cover and found this mess... it looked normal the last time it was off maybe a couple months ago.

I have been chasing issues of running hot but thought I finally got it with a recent new fan clutch. As part of the cooling system issues it seemed like I was losing coolant, but wrote that off to an old cap allowing the system to boil it away and replaced the cap. Can't swear that I haven't been losing some since though.

Seems like I've seen a pic like this on here in the past but I can't find it. Is this from coolant in the oil??

I recently checked compression and got the following dry/wet #'s:

1 = 125 / 125
2 = 90 / 100
3 = 95 / 100
4 = 92 /100
5 = 100 / 112
6 = 125 / 131

Anyone know what's going on here?
DSC04263 (Small).webp
DSC04264 (Small).webp
DSC04262 (Small).webp
 
Head gasket or cracked head leaking water/coolant. Does your oil look the same on the stick or when you drain it?
 
Last edited:
Motor Oil Mayo;)
 
Clearly a case of honey bees nesting in your valve cover. :D




Yep, you've got water-oil emulsion in there.
 
that's what I thought.

Ok, so the question becomes what to do in the dwindling time befor I leave for BHCC in a couple weeks.

Pull the head expecting a headgasket and head rebuild at min and hoping the bottom end is ok, or should I swap in a nicely running, good compression (all in the 130's), 95kmile engine out of my parts rig, and deal with this one if/when I get to it?

I lean to the latter, plus I haven't swapped an engine yet and kind of look forward to the experience. I'd expect to be able to do it in a couple weekend days...

Anyone got any thoughts one way or another?

thanks
 
Aliens have been making nests in there. Watch out for facehuggers when you clean around the valve springs!

If it was me and I had a good running engine available and the room to work, swap it in. Then you can take your time and overhaul this one without any pressure to rush the job. You can enjoy your 'cruiser the rest of the summer with minimal down time that way.
 
Your compression #s are low across the board. It's possible that a headgasket could cause that, but not likely.

I'd run with the parts-rig engine while figuring out what's going on with the slime maker.
 
I'd put in your parts engine too.

It's possible that its just a clogged pvc but I definatly think it's either a blown head gasket or a cracked head. Mine started to look like that when I had a cracked head.

Are you loosing coolant? I'd be a shame to rebuild the top end only to find that you still have low compression due to rings. It appears from your wet test you could just do a top end rebuild.
 
I gotta disagree. It's a hell of alot more work to install an engine/tranny/transfer than it is to change a headgasket. Pull the head, have it checked for cracks, you got ta do that anyway, and it only takes a couple hours tops. Assuming you have the parts readily available and no head repair/replacement is needed, a couple more will get it back together. Chances are the bottom end is fine, run it an hour, change oil, a few more hours, change oil, head for the bhcc. Otherwise, I see your truck sittin in the driveway in two weeks....nothing EVER goes as planned! Guys have spent two days or more just on a stuck pilot bushing...
 
drained the oil and it looks/smells like used oil... happy it didn't look like the baby poop stuff under the valve cover.

I'll let it sit awile and see if I get any kind of separation. Other than that, what am I looking for to confirm coolant in the oil?

Also curious for other opinions about Bull's question regarding humidity and the possibility that pretty solid recent Iowa humidity, plus a hotter than normal engine lately, could be the culprit. I tend to think no...

All a moot point unless someone gets me moving back the other way for a solid reason... been waiting for the reason to swap it out and the engine hoist I'm borrowing will be in the garage tomorrow.

thanks for the help
 
Condensate usually occurs when you make frequent short trips and the engine oil never gets to operating temps. Any moisture boils off if the truck runs for any length of time. Never seen condensation make that much poo. My guess is head gasket, along with everyone else. You can also run the truck and look for foam or bubbles in the radiator, just leave the cap off, just don't take it off when hot;)

GL

Ed
 
bull said:
If it was a head gasket wouldn't the oil he drained look orangish or gray? I wouldn't change it yet. Do you know anyone with a leak down tester?

I've seen valve covers look like that before and the head gasket was fine.



Have you overheated the engine?


I think I read in his post that the engine was running hot, also a sign of bad head gasket. If coolant is leaking into the cylinders and being compressed it could be forced past the guides? Maybe? It takes a fair about of something water-based to make that kind of emulsion. OTOH, a crack in the block would put more water in the oil?
Just speculating here:confused:

Ed
 
if you are looking to find coolant in the oil, bring a sample in somewhere. i dont know of auto chains that do it, but caterpillar service places do it and you should just be able to bring it in. they also show you a ton of other cool stuff too in the oil.
 
Let your engine cool over night and use a glass jar to catch the flow out of your oil pan. You only need to drain maybe a pint. Oil is lighter than water and if there is water in your oil it will be the first to drain out, assuming you are on level to front high ground.
 
After sitting overnight, I can definitely see some separation and discoloring in the oil I drained.

Bull, I don't know that it was overheated, but definitely got pretty hot at least a couple times.

Texx, I hear ya but am an going to swap the engines with tranny/transfer attached, so I'm optimistic the PIA factor will be minimized.

I'll post up results once I finish the swap and pull the head on this one.

thanks all
 
Back
Top Bottom