For Those in Hot Climates

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 1, 2006
Threads
211
Messages
1,010
Location
Dallas, TX
How high does your temp gauge needle go when in traffic with temps over 100 degrees?


It was about 107 yesterday and while stuck at a long light, I saw my needle rise to about 2 neddle-widths from the red zone..... once I got going again the needle went down to about the middle zone...
 
Mine stays dead middle here in Dallas and there when I lived in San Antonio. Either your guage is shot or you have a cooling problem. Interesting, weren't you having problems with the a/c cooling too? Fan Clutch ?

Just replaced mine proactively, never any cooling problems, but the a/c does blow colder at the traffic lights !
 
Without the temp mod to the stock temp gauge, I don't think it is very acurate. Instead of doing this mod, I just installed a Scangauge II. It gives me a numerical water temperature readout.

My truck was running at 200F-207F with outside air temps above 98F before doing a coolant flush and replacing the thermostat. It still was running hot at about 200F, so I removed the two big LightForce lights on the ARB bumper and water temps went down by 15F! Now it runs between 186F-195F with the higher temps in stop and go traffic.

By the way, I have the stock fan clutch & no auxillary fan, I also cleaned out the radiator from bugs and debris and straightened all the fins.
 
How high does your temp gauge needle go when in traffic with temps over 100 degrees?


It was about 107 yesterday and while stuck at a long light, I saw my needle rise to about 2 neddle-widths from the red zone..... once I got going again the needle went down to about the middle zone...

Mine was doing the exact same thing here in Houston. As soon as I got stuck in traffic, the A/C would stop blowing cold. At first I thought it was a climate control issue, but then I read a lot of posts about the cooling system and how the A/C would shut itself down when the temp got to around 227 F. This scared the sh*t outta me, thinking that my rig was running that hot.

First, I changed the thermostat and flushed the system. This did nothing.

Next, I changed out the fan clutch...some PO had put on an aftermarket for some dumb reason, so I went back with a OEM blue hub. This helped a little.

Finally, I changed out the 97 radiator to a 93/94 copper core. Voila!!! Fixed it all. Runs cool, A/C never cuts out...even in this friggin 104 degree Houston heat.

HTH!

:cheers:
 
Nice and toasty here in Phoenix. My needle never climbs above the 1/2 way point. Temporarily installed a manual gauge to verify once.

-Blue fan clutch with 20K CST, OEM radiator, JDM fan, Toyota red coolant.

***Edit*** Timing advanced to 10 degrees
 
Last edited:
I have already installed:

94 brass rad
10k oil in blue fan clutch
aux pusher fan in front of condensor
just flushed the system- new Toy red fluid w/ distilled water
Rav Temp Gauge Mod
Hood Vent

Havent seen the needle rise like this before but it has never been above 105 before either.....

Every other time it is in the middle....

only thing I can think is that we used a non OEM thermostat (was on a weekend) when we did the flush....

When parked/ stopped in traffic, vent temps when ambient temp was 106 was 65 degrees
When driving when ambient temp was 106, vent temps were about 58 degrees
 
I would also check your A/C evaporator. Mine was NASTY. After cleaning it, the vent temps are nearly the same when stopped as when moving.
 
yep.. that is the plan tomorrow!

Also, I have my aux pusher fan wired directly to the AC compressor power... I am going to change the wiring to SumoToy's suggested method... wiring to the Med Press A/C Switch.....
 
Summer temp is always on the mind when driving here in Phx.

My guage never goes above 1/2 way mark in my 93', but I have not modified it.
I installed a new OEM rad, thermostat, and replaced the hoses recently. Filled it with Toyota red and distilled H2O.

I have the blue fan clutch but still have to install it.
When I get the money, I plan on getting the electric fan also.

See if your rad is clogged with the sludge some have reported.
 
My rad is 2 months old.... it better not be clogged!! :)
 
We get over a 100 here in Missouri once in a while. I've never had the a/c kick out. Needle stays for the most part in the same place. I've never sat in gridlock or anything. But I've had extended ideling periods an hour or two, with no issues.
 
I just had this problem in memphis, had truck running in drive way to cool it off before putting the kids in it. Got in and gauge was just past 3/4 way to the red line. Went down as soon as i started driving. Flushed the system the next weekend and it hasnt done it since...let it idle in driveway for about 45 mins and never went above 1/2 way after the flush.
 
Know someone with a scangauge you can borrow? maybe it would help to see actually what temp's your running.
 
Stock gauge, new radiator (temp stayed same with old) red fluid, original water pump and thermostat in georgia - never goes above 1/2 cool area

sounds like your not moving enough air when stopped, any chance pusher is blocking more than helping? X2 on blockage from condensor?
 
Never have had any issues with my 3FE overheating, the only time it overheated was when the original radiator blew 2 years ago.
When it happened, it was sudden w/o warning...sounded & felt like i drove over an IED.

I see a lot on here about some 80's getting hot, is this another FZJ thing? :D
 
Our temperature is hot all year around and even with the busted fan clutch (about three weeks ago), the needle seldom passed the half way mark. I have an additional electric fan.:steer:
 
Just to give you guys a heads up on the stupid water temp gauge, mine doesn't even move when the Scangauge was reporting a temp of 213*. So, I wouldn't rely on the needle width for your temp analysis unless you've done the temp gauge mod!
 
Back
Top Bottom