FJ80 Fuel Pump life expectancy

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 10, 2015
Threads
11
Messages
46
Location
Texas
I have a 93 FJ80 with 180,000 miles on it. I'm starting to have some issues with it running very poorly. Seems to run better when cold but as it warms up. I have replaced fuel filter with an OEM one today. What is the life expectancy of the 80 fuel pumps? I am looking for a way to test the fuel pump is working correctly if anyone has any suggestions i'd appreciate it. Also any other things to check?
Thanks
 
You might want to check your fuel pressure. As for the 'life expectancy' of the fuel pump, it will vary. Mine is the original (1997) and I have 306K on my rig now.
 
... What is the life expectancy of the 80 fuel pumps? ...

When one dies, will let you know! I have never seen a dead one, likely has happened, they are very durable. A better description of what if going on, what code(s), etc, would be helpful.
 
When one dies, will let you know! I have never seen a dead one, likely has happened, they are very durable. A better description of what if going on, what code(s), etc, would be helpful.


I have never seen one either, and lot's of rigs with ton's of miles, an amazing part that keep's working
 
Have a 1HDT fuel pump that at 600,000km was worst for wear with inefficiency running with vibrations over the rev range. Had this rebuilt with a DENSO specialist and now good as new. What I learned was that at 250,000km wear and tear starts.
 
80 Series fuel pumps have a pre-filter that is replaceable. Some call it a "fuel sock" for an unknown reason. In any case it's one of those 100K mile items that should be replaced once in a while, along with all the associated gaskets and cushion. All OEM parts are still available.
The pre-filter for the 1FZ-FE equipped trucks is 23217-16490 and will set you back around $12.
If you search on this forum a bit, you'll find a list of associated parts.
 
Have a 1HDT fuel pump that at 600,000km was worst for wear with inefficiency running with vibrations over the rev range. Had this rebuilt with a DENSO specialist and now good as new. What I learned was that at 250,000km wear and tear starts.
He’s got a gas engine with an electric in-tank pump, not a diesel IP
 
Have read of several Fuel Pumps with 400K miles + on them. Not a change on interval item. Water Pump is another that is very long lived.

I changed both the (sock) Filter on the Pump and the Fuel Filter under the intake. Rig has 200K and both were in decent shape. I posted write ups on both. Fuel Filter had a real fine gray silt, but would not have blocked flow or clogged injector.

**If you like buying and changing Parts, Old Jeeps are perfect for you.
 
Last edited:
You might want to check your fuel pressure. As for the 'life expectancy' of the fuel pump, it will vary. Mine is the original (1997) and I have 306K on my rig now.
I have rented the fuel pressure gauge to test pressure I'm trying to find where to hook it up to on the engine.
 
After opening up the service door for the fuel pump and turning the ignition on but not starting the engine, im not hearing the pump prime itself???
I checked the fuel pump resistance if I follow FSM it points out what terminal 5 and 6 are. My readings for 5 and 6 terminals are 0.00 or am I reading the terminals wrong as the other two are reading 2.26 resistance.

IMG_20190202_100315.webp


Fuel Pump resistance.webp
 
Looks like the connector for the fuel pressure gauge is the banjo type which doesn't come with the kit I have. So can't test pressure ATM.
 
The fuel pump on 80 & 100 series L/Cs does NOT prime until the ignition cranks the engine. So listening for it at the ignition 'on' position can not be used as a diagnostic tool.

There is not a factory access port on your fuel rail to check the pressure. You have to install a banjo bolt adapter.

'Search' How to check fuel pressure.
 
Thanks Jonheld, I am running out of ideas to determine if the pump is functioning correctly. If anyone has any input on the pump resistance on terminal 5&6 post from above I'd appreciate it. Thanks
 
Thanks Flint, I will need to source a banjo bolt adapter.
 

That clip should be connected to the mount, they break, allowing the harness to contact the hot EGR pipe. This can cause whatever wire(s) are close to the pipe to short, can make running problems, mostly when under load. First step is to tie the harness in place, it shouldn't be allowed to move around.
Harness_zip_1.webp
 
Back
Top Bottom