Control Arm Drop Brackets???

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 10, 2017
Threads
26
Messages
95
Location
Fayetteville, AR
So I've decided to go with an OME 2.5 lift on my 97 LC. I'm doing heavies up front and medium in the back with my current setup of ARB/winch combo. I've also decided to not go with the castor bushings but do drop brackets. Since 2.5" drop brackets aren't available, do I go with the 2 in. or 3 in.?
 
2" will yield less caster correction (but probably enough to put you back in spec), but you'll lose less ground clearance under the truck if you're concerned about getting hung up on a rock or stump.

3" will yield more caster correction, but hangs down further. If you anticipate ever adding a spacer in the future, you might want to start with 3".

Also, IIRC, they do not drop the mounting point by *exaclty* two or three inches, but something close.
 
2" will yield less caster correction (but probably enough to put you back in spec), but you'll lose less ground clearance under the truck if you're concerned about getting hung up on a rock or stump.

3" will yield more caster correction, but hangs down further. If you anticipate ever adding a spacer in the future, you might want to start with 3".

Also, IIRC, they do not drop the mounting point by *exaclty* two or three inches, but something close.

That makes perfect sense. Thank you.
 
MAF 2" are good up to 3" lift. They actually correct more than just 2" of lift.
3" are simply too big (hanging down). If you end up loading the car more, (sliders, skid plates, rear bumper with spare tire on it, some gear), you will end up with less than 2.5" lift you originally installed. Even if you end up installing some spacers to bring up more, to where it was in the beginning, you will still be within spec.

People usually run 1.5" - 2" lift without any correction.
 
I measured my 2" drop brackets at 2.5" drop on the nose. My pass side holes needed about a 1/8" of round file work to get it to bolt up.... I have read this many times from others posts. Nothing is ever just bolt up...
 
If you have access to a welder, or friend with welder, drilling some 5/8" holes will save you quite a few dollars on parts. Also, no change in ground clearance. And the ability to lengthen the wheelbase slightly.

I've done this twice on two different trucks. Drilling is a bit of a misnomer, we ended up using a die grinder more than the drill. And welding the washers can be done after adequate caster is confirmed. A muffler shop or body shop, or a good alignment shop will have a welder to zap them in place. I also gained a smidgen of extra ride height due to 'squareing' off of the spring perch.
 
I tried to do the washer mod and the drilling aspect kicked my ass. A GOOD beefy 90* drill is mandatory!!!!
 
I tried to do the washer mod and the drilling aspect kicked my ass. A GOOD beefy 90* drill is mandatory!!!!

We used a small drill to get the 1/8" pilot holes before doing anything else. A 90 deg drill would have been handy, but we didn't have one. Truck isn't nearby so I can't post a pic, plus it's night time, and covered with dirt. The rear hole we moved back and slightly up to restore lost wheelbase. Can't go up much or the arm will hit the housing. The front hole moves back and down as far as you can get it. When we were done, we got 2 deg caster with 850/860 springs. Was it worth it? Yeah, because we could spend the $$$ on gas and go somewhere. Also it's handy to have access to an alignment rack.

3 banana job. Maybe 4 if it's your first time at it. Would do again. Tag team it with a buddy. Ear plugs, eye protection, heavy duty air drill to make 5/8" holes, because electric drills are too fat to get in close. Probably took a two or three hours of cussing....
 
Not sure why everybody is so against the drop brackets .. they work great and put you back to factory spec ...

Because if you use your 80 off road they are terrible. Hang up everywhere. Expecially in reverse. Why even bother with them when you can use castor plates?? Poor choice if you do
 
I recently developed caster plates for a 2.5" lift. I targeted 3* of caster when the truck was sitting at 2.5".

To mimic the hole position to achieve those results using a washer mod technique would place the washer off the edge of the axle bracket.

How much are said caster plates and where would one go about ordering them?
 
So we have every flavor under the sun. That's why vanilla is not the only flavor ice cream in this world.
Drop brackets are good for a guy without a welder or 20 ton press. Most 80 owners don't hardcore their rig. Brackets will be fine for most 80 owners, but not all.
It is good to have different options. There is drawbacks to each design ie plates, brackets & bushings.
 
Last edited:
Back
Top Bottom