Considering 35's - Need Gearing Advice

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 13, 2006
Threads
48
Messages
322
Location
Where the glaciers stopped.
Ok - My 80 is no longer the DD. Sad and happy all at once. I already miss driving her to work in the AM, but now I can really be more trail oriented in the remainder of the build.

Keep in mind that I am not a mechanic by any stretch....but can maintain the rig to a degree, add most mods myself and troubleshoot some things.

My 33" BFG Muds are worn out. Added sliders and a built-in tool box recently and I need to raise the truck back to where it was before the weight got added.

"Hello, my name is Tom and I am a Cruiser addict" so naturally 35" tires are now the way to go. BTW - I am running ~ 4" lift. OME heavies with 1.5" spacers.

So, I am doing my homework regarding gearing. I found out that a stock geared 60 series on 35" tires can add too much drivetrain stress and bust a tranny. 1) Is that the case on a FZJ80?

2) Considering the 35's, will I need to regear if I am satisfied with road performace and don't mind using the throttle offroad? 4.88's seem to be the consensus if necessary.

3) What else do I risk breaking in the drive train if I add 4.88 gears and 35" tires? Birfields?

4) If I decide to regear; is that an optimal time to add lockers?

As always, I appreciate your input. :steer:
 
1) dunno bout that one, lets hope not.
2) if you are satisfied i dont see the need to regear, minimal mpg's if you run lots of highway.
3) from the mods alone? not much birfields or axles, but its where those mods will take you that might lead
twisted driveshafts, wrinkled sheetmetal, and busted drivetrains. :)
4) yes it is ideal time, minimal extra labor once inside to set up the arb, it'll all be out on the work bench.
 
gears

I have had a couple of fzj80's myself setup similar w/ 35's and 4.88's, and overall was happy with the performance. We have regeared many of these trucks, and 4.88 and 35s is best for most people. Some really heavy trucks, or ones used at altitude, or those that dont mind a few more rpm's are happy with 5.29's.


Ok - My 80 is no longer the DD. Sad and happy all at once. I already miss driving her to work in the AM, but now I can really be more trail oriented in the remainder of the build.

Keep in mind that I am not a mechanic by any stretch....but can maintain the rig to a degree, add most mods myself and troubleshoot some things.

My 33" BFG Muds are worn out. Added sliders and a built-in tool box recently and I need to raise the truck back to where it was before the weight got added.

"Hello, my name is Tom and I am a Cruiser addict" so naturally 35" tires are now the way to go. BTW - I am running ~ 4" lift. OME heavies with 1.5" spacers.

So, I am doing my homework regarding gearing. I found out that a stock geared 60 series on 35" tires can add too much drivetrain stress and bust a tranny. 1) Is that the case on a FZJ80?

2) Considering the 35's, will I need to regear if I am satisfied with road performace and don't mind using the throttle offroad? 4.88's seem to be the consensus if necessary.

3) What else do I risk breaking in the drive train if I add 4.88 gears and 35" tires? Birfields?

4) If I decide to regear; is that an optimal time to add lockers?

As always, I appreciate your input. :steer:
 
Ok - My 80 is no longer the DD. Sad and happy all at once. I already miss driving her to work in the AM, but now I can really be more trail oriented in the remainder of the build.

Keep in mind that I am not a mechanic by any stretch....but can maintain the rig to a degree, add most mods myself and troubleshoot some things.

My 33" BFG Muds are worn out. Added sliders and a built-in tool box recently and I need to raise the truck back to where it was before the weight got added.

"Hello, my name is Tom and I am a Cruiser addict" so naturally 35" tires are now the way to go. BTW - I am running ~ 4" lift. OME heavies with 1.5" spacers.

So, I am doing my homework regarding gearing. I found out that a stock geared 60 series on 35" tires can add too much drivetrain stress and bust a tranny. 1) Is that the case on a FZJ80?

2) Considering the 35's, will I need to regear if I am satisfied with road performace and don't mind using the throttle offroad? 4.88's seem to be the consensus if necessary.

3) What else do I risk breaking in the drive train if I add 4.88 gears and 35" tires? Birfields?

4) If I decide to regear; is that an optimal time to add lockers?

As always, I appreciate your input. :steer:

4.88 are the safe and tested way to go. That tranny is a bus tranny and is very strong. The only real weakness in an 80 is the Birf cage. You may or may not break a cage.

And yes I would do the lockers at the same time as you regear. Why spend the time and money again later.

Also get yourself a FOR or at least Slee lift kit. You will be much happier.

:cheers:
 
If you are locking spend the money on regearing. You can wheel an 80 on stock gears and 35's without a ton of throttle, but if you are planning serious wheeling (rock crawling), you'll want to regear.

What are you after in performance? I wouldn't say 4.88's are a consensus. I would say they hit the widest area of usage, meaning you retain the function of overdrive at top highway speeds while gaining lower gearing. 5.29's take away about 80% of overdrive and are best for a more dedicated wheeler (extra crawl ratio) and 65-70 mph highway speeds.

I love the 5.29's as taking away OD is a reality at my altitude anyway and they rock offroad, but that top speed RPM issue must be carefully considered.

I assume you know that 35's are going to rub on OME heavy at full compression if you crawl unless you have swapped to L shocks?
 
I assume you know that 35's are going to rub on OME heavy at full compression

Hell, my 33's rub under full stuff-age with OME heavy lift. Nearly torn my front 'flaps' off becacause of that.
 
No bus tranny on the 95-97 80s. that was in the earlier years. So where the glaciers end is pretty vague. Was this when the last ice age was or a current glacial retreat(could be just about anywhere but far souteast USA)?
1 not likely
2. again may be based on where you live
3. As other have said, birf cage
4. yes if you want lockers at some point in time
I do not agree about the suspension. If you are doing jsut expedition type of travel you have a really great and stable set up. If you want more rock crawling and flexy set up then maybe the others will get you what you want. Easier to decide what you want before you buy the set up.
good luck, Robbie
 
I'm a vet at saying I love our 5.29 gears on 35s. I've driven them from Seattle to Moab and back, and Seattle to Rubicon and back, and RPMs and driveability has never really been a problem. Around town you won't even notice anything.

Then when you get off-road--they RULE.
 
I really like my 4.88's and 35" Toyo MT's. I enjoy the lower gearing off road and still can drive 80-90MPH with no issues on the highway.

I would disagree with Nay that 5.29's are better for the altitude, but thats my opinion.

I switched from Heavies to J's with L shocks. An easy mod.
 
Re-cap

Let's see if I have this straight.

1) The 35" tires do not cause extra stress on the tranny/drivetrain that regearing w/4.88's would alleviate.

2) With 35's the stock birfield cage would still be vulnerable with the 4.88's installed.

3) Re-gearing is mainly a preference thing for the driver.

4) Since I am not doing a lot of rocks and don't live in the mountains the stock gears may be fine for the trail riding I do. Also, want to be able to go 80mph if i need to. :steer:

Also, I assume the lift satisfaction from the FOR and Slee lift kits is from a crawling point of view. What would I gain on the trail - I do not want to be taller than 35's with my 4" lift. Can't really fit on the trails where I go as it is. It's always tight out there.

Please chime in here. This has been very helpful already.
 
Let's see if I have this straight.

1) The 35" tires do not cause extra stress on the tranny/drivetrain that regearing w/4.88's would alleviate.

2) With 35's the stock birfield cage would still be vulnerable with the 4.88's installed.

3) Re-gearing is mainly a preference thing for the driver.

4) Since I am not doing a lot of rocks and don't live in the mountains the stock gears may be fine for the trail riding I do. Also, want to be able to go 80mph if i need to. :steer:

Also, I assume the lift satisfaction from the FOR and Slee lift kits is from a crawling point of view. What would I gain on the trail - I do not want to be taller than 35's with my 4" lift. Can't really fit on the trails where I go as it is. It's always tight out there.

Please chime in here. This has been very helpful already.

I have 35s with 4.88 and for what I wheel 5.29s would be a mistake. One thing about running lower gears is that you will reduce the stress on the t-case and tranny and the engine will rev higher off road giving better cooling and power steering assist. So it's not all about the birfs.
 
It's really about personal preference so, as another option for you to consider, I thought I'd mention that I have 4.56 gears with 35s and this keeps everything pretty close to stock (ie accurate speedo). Performance is fine for my needs...
 
Let's see if I have this straight.

1) The 35" tires do not cause extra stress on the tranny/drivetrain that regearing w/4.88's would alleviate. .

I see you have a 97 its not the biggest tranny but still very strong. 35s are pushing the limits of the truck but it works pretty well. And the only weak points are the birf cage and maybe the steering (sector shaft and power).

2) With 35's the stock birfield cage would still be vulnerable with the 4.88's installed. .

Yes but look at all the guys pushing there truck hard with this setup and yet they don't break that much. One more thing I think it is good to have a weak point like a brif or a drive line. Better that then a fragged tranny or t-case right.

3) Re-gearing is mainly a preference thing for the driver. .

Yes, It was right for me. I know many people that had this setup and liked it. Also I don't drive over 70 I am a slow driver but I wanted the option If I wanted to and I didn't like the RPM # at 60 to 70 with 5.29s And most people felt that 5.29s with the weight I carry would be more prone to breakage etc.
 
Also, I assume the lift satisfaction from the FOR and Slee lift kits is from a crawling point of view. What would I gain on the trail - I do not want to be taller than 35's with my 4" lift. Can't really fit on the trails where I go as it is. It's always tight out there.

Please chime in here. This has been very helpful already.

NO not at all. I am more of a expo wheeler, what I am trying to tell you or say is that these kits are better. They are or were put together by smart people from the ground up to be used on your truck with 35" tires and at that height.

It is something that you just have to feel maybe, I don't know if I can explain it to you. I'll I know is that I don't know anyone that has a 4" Slee kit and had J springs or an 2.5" lift or both before that would not say that there new kit is better then what they had. I know people that had or tried a 6" or bigger lift and didn't like it but not a 4".

Also everyone that has tried a FOR kit says its like night and day to what they had before.

I'm not saying that what you and others have is not ok, it just isn't ideal. Its smart to start with a good fundation not just make it work. That is if you can afford to.

I hope this helps a bit.
:cheers:
 
One more thing


Get the right castor for the lift

Talk to Landtank

:beer:
 
Let's see if I have this straight.

1) The 35" tires do not cause extra stress on the tranny/drivetrain that regearing w/4.88's would alleviate.

Somewhat, but the stock trans/drive train is pretty stout and well proven. That said, anytime you add more loads, becomes more important that you step up the maintenance and keep everything in top condition.

2) With 35's the stock birfield cage would still be vulnerable with the 4.88's installed.

Anytime you add more load/stress (more HP, more aggressive wheeling, bigger tires, more weight, etc) drive train parts are more likely to break. If well maintained in good condition, the stock birfs are pretty stout. Do a search, you will find a few that have broken, but no where near an epidemic. The next question for the broken ones is, were they high miles, unmaintained, clickers?

There are a bunch of 80's in our club, most of enjoy challenging their rigs. I have been on many runs, 3.5 - 4+ trails, many on rock, most rigs locked, many with 315+ tires, doing most of the "no-no's" worried about here, like reversing locked on rock, etc and have only seen one birf broken. It was on one of the best maintained rigs in the club, broke on flat sand. When we got it apart it had a factory defect and had been cracked for a while. Anything can be broken, but IMHO the stock birfs are stout and can take much more beating than many here give them credit for.

3) Re-gearing is mainly a preference thing for the driver.

4) Since I am not doing a lot of rocks and don't live in the mountains the stock gears may be fine for the trail riding I do. Also, want to be able to go 80mph if i need to. :steer:

My rig is rolling on 37x12.5" tires and stock 4.10's, around town and rolling down flat highway, it's fine, yes there is a loss of power, but it's drivable. Any mountain grade and it's over, way slow. It wheels much better with the big tires than the 295's. That said I have a set of 5.29's, when they are installed I'm sure that I will be much happier.

Also, I assume the lift satisfaction from the FOR and Slee lift kits is from a crawling point of view. What would I gain on the trail - I do not want to be taller than 35's with my 4" lift. Can't really fit on the trails where I go as it is. It's always tight out there.

Please chime in here. This has been very helpful already.

35"s will work great with your setup, brother Brian and a bunch of other local club members successfully run the heavy rear, spacer or J's front with 35's. I have most experience with the Nitto 315's, they only lightly rub the rear inner sidewall to fender well when fully flexed, aggravating, but not going to hurt anything. Most add a short bump stop spacer to eliminate it. If you add the spacer, replacing the rear shocks with L's will add some travel, flex.

Some prefer the stiffer springs, but I'm happy with the OME ride/flex for my rig, if anything would prefer slightly softer springs. Most of this depends on the rig setup, weight and driver preference.

Brother Rob has had the 315's for 3yrs/40K mi, with stock gears, on his relatively well maintained 160K mi rig. He wheels as often as possible, 3, week+ trips to Moab, many local 3.5-4 trails, mostly on rock, without any drive line failure, I don't think he has even replaced a u-joint. He has a set of 4.88's that will be going on shortly, that will probably improve his setup, but we have had some killer wheeling trips with the stock gears and he can out wheel me when I have the 295's, no problem.

If you want 315's bolt them on! You will notice a power loss and less compression braking. But gain clearance, ease in rolling over obstacles, overall it will be a more capable wheeler. It comes down to your needs and expectations, how tolerant you are to the power loss, etc.:D
 
315's with 850J front, 863 rears. IMHO 4" would be ideal with 4.56 if your faily flat or 4.88's. I have been running stock gears on mine - has more pickup than my 60 had, but is geared a little too high for my tastes for moderate wheeling.
 
I Cruised on 315s w/Js, and stock gears for about 4 years. Did just fine overall.

However, I do believe hauling arse up and down the highways through the mountains of NC, Tenn, SC, Ga and WV did wear on my trans somewhat. But she's still going strong, I just have to make sure I'm at a complete standstill when switching from forward to revers; go figure....I get the slight slip for a moment here and there.


Anyway. I'm rolling on Slee's 6" and 36x12.5/16 TSL SXs now with 4:88s from ringpinnionbiz; for about a year now. I lost a lot of sleep(and still do) debating 4:88s versus 5:29s. I opted for 4:88s because the 5:29s are slightly weaker, run higher rpms which "could" overheat the engine plus some. Worst thing you can do is overheat a Cruiser engine.

As she stands, the 4:88s are just fine for what I do, mine is an unplanned DD again too with over 200K. The 36 Swampers turn just fine, Low 4 is good to go for around here. RPMs are where they ought to be, even at highway speeds that still really don't exceed 80 mph because of the unbalanced Swampers.
 
As she stands, the 4:88s are just fine for what I do, mine is an unplanned DD again too with over 200K. The 36 Swampers turn just fine, Low 4 is good to go for around here. RPMs are where they ought to be, even at highway speeds that still really don't exceed 80 mph because of the unbalanced Swampers.

I could say "I'd like to cruise @ 80 mph", but the fact is, my tires really don't - the mechanical bits don't mind those speeds/RPM's at all and the powerband of the engine loves it. I have absolutely no aspirations to run 90 mph on a lifted 4x4 with soft 35" mud terrain tires. I'm not a safety hound at all - I'll run no problem fully loaded without a front swaybar. You get into emergency maneuvers @ 90 mph and you better hope that ARB is the gift from heaven you think it is.

The idea that 4.88's are enough of a strength safety margin over 5.29's is silly. You are talking one tooth on a 40 tooth ring gear. The quality of the install and how you drive is going to be a much greater factor. All of these people who are convinced that they would bust a 5.29 but are sure 4.88's are just fine are probably spending quite a bit of time onlooking at the bypasses :flipoff2:

Having said that, most people will prefer 4.88's. I wouldn't plan to stay on stock gears forever with 35's - it will get old driving it. The drivetrain can handle it, that's not the issue. It's driver fatigue over the years.
 
Back
Top Bottom