Center Dif lock relay bad?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 29, 2016
Threads
19
Messages
609
Location
North Alabama
Attempted to lock the center dif with dash switch and heard lots of clicking from the drivers kick panel. Eventually locked but now the switch does nothing and when I attempt to lock by shifting to low, I get clicking but no lock or diff lock/ABS lights on the dash. At times, shifting to low gets no clicking from the relay at all. It does shift into low gear. I placed new front and rear dif lock position switches a week ago since they would lock but flash on the dash. I haven't touched the center dif position switch. Coincidence or not, the PWR button isn't working either.
 
Bummer.

I'd look at my fuses.
 
If it worked for awhile & you didn't smell burning wires, time to spend quality time with your process / multi meter, a test light, etc.

Fusible links good?

What else went down?

Did you crawl under & verify the socket plug & wires are all hooked up & no corrosion or snagging from last time out in the woods/rocks?

The PWR switch just changes tranny shift points, did you burn the cluster bulb out, the backlight to it, or what?
Did you lose pwr to the PWR switch, and if so what else?

Might want to really check that fuse too with a ohmmeter, looks can lie.

Download a EWD for your year 80, it'll help with current flowpaths.
 
Remove the relay and test it per the fsm.
 
Looks like the logical step to take. Was hoping for a Hail Mary quick fix as electrical trouble shooting is not my strong suit.

None of us were born wire guys, we all had to figure it out.
Part of the "shared group pain" of classic rides.
 
Linus, you're thinking like I am. "What has changed or what have I done lately that initiated this?"

1)Disconnected battery so I could take off the steering wheel and recover.
2)Pulled the cluster to replace burned out bulbs. The new "D" bulb lasted a few days and is out again. Curious.
3)Installed new head unit/speakers; new bulbs in HVAC. So had all the switches out and back in.
4)New trans shifter bulb so had PWR switch unplugged. Don't think it's worked since. But 2nd button works and both are illuminated on the switch. I believe I've read that they have separate power supplies. So either no signal from the switch or something is interrupting its signal to the dash bulb AND ECU.

I rechecked the PWR and CDL switches to make sure I pushed the connectors all the way in upon reassembly.
Truck has only been driven around tow as I'm doing all this.
 
Suck as it may, I'd make a list of all the crap that went down on you & look for common power taps. Even all the little backlights that never came back, since maybe they blew prior due to prior owner history.

Any electrics or electronics wired into your dash, like aftermarket radio, etc?
I'd pull the power to them, see if it's a bad actor.

I'd also check the light rings for the other trans gears & see if it's just 'D' or if you lost power to 'P, R, N,....2, 1' as well if you are there.

Has to be a jostled wire in that dash area you just got into, a short or a connector with tarnished / corroded taps.....maybe a multiplug not fully seated, like the cluster ones when you do it with the wheel still installed.

Hopefully not chasing prior owner hinky crap, but a possibility if you had a ton of blown backlights (have /had a 135K, a 230K, and a 360K '97s - alot of bulbs go between 230 & 360K, according to my 360K dash when I started with it.)

Glad I said suck advice up front, yeah?

Top tip - Add a sig line or detail your model, it's helpful & may attract a guy who knows your era 80 - IDK jack about 3FE years or early dashes, I'm a 3x '97 owner.
 
Pull the switches and manually manipulate and or exchange with a known working switch, you could even hot wire the plug to verify circuit to dash. If wires to dash illuminate then you have a b/o switch.
Hardly worth the effort to clean so by new or grab some off almost any Toyota at your local pickers. Get a handful of them!
 
Pull the indicator switch plug on the tcase put a jumper in the harness side now go shift to low, if light comes on switch is bad or gummed up if no light then either it's burned out or problem is not the switch
 
It appears that the CD lock indicator switch and the 4L indicator switch are not identical parts. The CD lock indicator switch is the same as the front/rear diff indicator switches but the 4L has a different plug on it. Anyone know if this is normal and if so, what the 4L indicator switch part number is?
 
Pull the relay and test it. Apply 12VDC to coil contacts, connect a multimeter set to resistance to the input and output contacts and watch what happens as you apply power. Do this over and over to verify consistent operation. Sounds like the relay is internally broken.
 
Excellent idea! I did that last week and the relay tested normal. Next step was the 4L switch and CDL switch. Since I'm working solo, it's easier to just replace the switches than jump the contacts...unless you get the wrong switch, which apparently I did.
 
Back
Top Bottom