CDL switch installed but no light when on

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 7, 2014
Threads
10
Messages
51
Location
San Antonio, Texas
I've got a CDL switch installed. Power to the switch is good. When pressed, I can hear the relay engage but no light on dash. How can I determine if actuator is engaging? All other dash lights appear to be in working order. This is on a 93. Thanks for any input.
 
jack up one front or rear tire.
If you have diff locks make sure they are NOT engaged.

Transmission in Neutral.
Engage CDL switch and listen for relay activation.

Rotate whichever tire is in the air.

If it hits a hard stop point.. CDL engaged. If it is hard to turn but does turn, CDL is not engaged and the viscous coupler is providing the resistance. Note that between all of the splined couplers, bearings, driveline slop, etc.. there will be a LOT of play back and forth before resistacne starts.. you need to apply constant force against the tire in one direction and keep turning, see if it stops turning all of a sudden.

note that for this to work 3 wheels need to be on the ground and the transmission in neutral.



Edit: dash light not working is common.. though it usually isn't the light itself. It is a secondary switch on the transfer case that tells the light and other systems that the CDL is actually engaged. This switch is what fails so often.
 
set a jump wire to the L4 position switch too. I believe both switches (which are the same unit) have to be operative for the dash light to work. I just had a case where both switches were bad and not until I replaced both did the dash light come on. If your CDL switch is new and working then just by jump wire on the L4 switch the dash should light (unless the dash bulb is bad). If the L4 jump wire lights, replace or rehab that switch and you'll be good to go.
 
The CDL dash switch accomplishes the same thing as the L4 position sensor switch. If you hear the relay when pressing the dash switch then the CDL is being energized. More than likely the CDL sensor switch on the front of the transfer is not working.therefore the dash indicator lights remains off even if the CDL is actually locked. You can then check the CDL as stated above by raising one wheel.
 
Does the light work when you put the trains in low ratio? Did it ever work?
The cdl switch imitates putting the selector lever in low ratio as far as the center diff lock actuator is concerned.
 
Thanks for the replies! Much appreciated. Here's what I did this morning. Jacked up passenger front side, neutral diff licks off, center diff switch in off position. Could not rotate wheel. Engaged CDL switch with same result. Tried same on rear driver side with same result.
 
when I said the switches I mean the CDL sensor switch on the T Case (forward side) and the L4 sensor switch on T Case (rear aspect). Not talking about the installed dash switch.

I installed a dash switch, no lights (no lights before either when shifting into Lo). Set a jump wire on the CDL sensor switch and rehabed the L4 sensor switch (again both on t case) and boom! got a light on the dash.

That's when I realized both sensor switches on the Tcase were not working right. These are Beck Arnley backup light switches and easily available for about $18 each. According in info on this forum they don't run enough current to stay contact clean and operable and seem to often need rehab or replacement.
 
when I said the switches I mean the CDL sensor switch on the T Case (forward side) and the L4 sensor switch on T Case (rear aspect). Not talking about the installed dash switch.

I installed a dash switch, no lights (no lights before either when shifting into Lo). Set a jump wire on the CDL sensor switch and rehabed the L4 sensor switch (again both on t case) and boom! got a light on the dash.

That's when I realized both sensor switches on the Tcase were not working right. These are Beck Arnley backup light switches and easily available for about $18 each. According in info on this forum they don't run enough current to stay contact clean and operable and seem to often need rehab or replacement.
Thanks much!
 
Thanks for the replies! Much appreciated. Here's what I did this morning. Jacked up passenger front side, neutral diff licks off, center diff switch in off position. Could not rotate wheel. Engaged CDL switch with same result. Tried same on rear driver side with same result.

neutral diff licks off?

axle diff locks off.
transmission in neutral.
transfer case in H (or L if you've done pin 7 mod)
CDL dash switch NOT pressed.

Jack up one tire and see if it spins (it should. slowly, but it should)

Hit CDL dash switch

See if tire won't keep spinning.

I forgot to mention earlier that if your case is in Low and you haven't done pin 7 it'll try to engage CDL.. so xfer in H
 
One tire in the rear and one tire in the front must be jacked up at the same time

And to clarify what should happen;

If dif lock is working then the tire in the front should turn the SE direction you are rotating the tire in the back.

If the diff lock is not engaging it will spin the opposite direction.

Another test is to engage the lock via the switch or shifting to low (FYI- 7 pin mod is for dash switch only control. T case position has no bearing on engagement if you've done this mod)

Drive the vehicle in a circle in a dirt or gravel lot (low traction). You should hear a scrubbing noise, like a tire scuffing, if the diff is locked. Make sure you unlock the diff when done.

Edit: bloc's method should work too, his and mine are similar yet different methods. Sorry to confuse you.
 
Back
Top Bottom