CDL Mod (who can help?)

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 5, 2006
Threads
107
Messages
526
Location
USA
I am outfitting a 94 FZJ80 for Africa

It already has 3in lift and 315/75 MT and no lockers, someone has suggested that I install a Aussie in the rear... is this GOOD? or BAD? I will be driving on thousands of miles of dirt roads, some of them very muddy.

I would like some help installing the CDL mod...if anyone has done this before... also Looking for a good winch/bumber combination and any other thoughts about what I should do to it before I ship.

anyone do the PHH? I need some assistance.

I will be baseline-ing it, with new oil, plugs, wires, etc.

Thank you in advance;)
 
Last edited:
I am outfitting a 94 FZJ80 for Africa

It already has 3in lift and 285/75 MT however I would like some help installing the CDL mod. also Looking for a good winch/bumber combination and any other thoughts about what I should do to it before I ship.

I will be baseline-ing it, with new oil, plugs, wires, etc.

Thank you in advance;)


Checkout the Slee site:

Slee - Electrical Switches
&
Slee - Pin 7 Mod for CDL (Toyota 80 Series Land Cruiser)

HTH

Edit: See Cdan for CDL switch - best price!
 
Last edited:
Where are you?
 
X2 on Slee's installation instructions. The CDL switch is plug and play.

For a good bumper/winch combo with good front end protection it's hard to beat an ARB bull bar with a Warn 12K winch.

On top of the basic items I would look at replacing the coolant system hoses, including the PHH, if they haven't been replaced.
 
I'd be glad to help if you're in or want to come to Southern California!

CDL switch, as mentioned doesn't hardly even rate :banana:

c'mon down. Dan.
 
Thanks guys!!! I am presently located in Salt Lake City...however we will be loading out of Chatsworth, CA in January.

I will order the Slee CDL and one PHH
 
Thanks guys!!! I am presently located in Salt Lake City...however we will be loading out of Chatsworth, CA in January.

I will order the Slee CDL and one PHH

save yourself about $60 bucks -
get an emergency flasher switch from a junk yard and use that. same contacts/ connector.
It shoudl be $5 bucks at the local scrap yard.

also, use the search feature here. that PHH is a bitch to change. get the silicon version here:
Silicone
 
I am outfitting a 94 FZJ80 for Africa

It already has 3in lift and 315/75 MT and no lockers, someone has suggested that I install a Aussie in the rear... is this GOOD? or BAD? I will be driving on thousands of miles of dirt roads, some of them very muddy.

I would like some help installing the CDL mod...if anyone has done this before... also Looking for a good winch/bumber combination and any other thoughts about what I should do to it before I ship.

anyone do the PHH? I need some assistance.

I will be baseline-ing it, with new oil, plugs, wires, etc.

Thank you in advance;)
 
If it really is that muddy, skinnier tyres with knobles on the shoulders (think landrover) might work better - big wide ones can slide around on the surface, wheras skinnies dig down to the firmer stuff. Depends on the (overall) terrain. Wide is great on dust roads.
 
Where in Africa are you headed? I'm headed there in a few more months with my 96. I'm planning on 285's with no lift, armored rear quarter panels, belly plate, front mounted winch, CDL switch and mods, reinforced lower control arms, upgraded steering relay rod, sliders, dual batts, and a snorkel. I'm also planning on taking some spare EFI relays...

I've already baselined the truck and I figure this setup should allow me to go up and over just about anything I'd be willing to try with my little ones in the car.
 
I will be in Liberia....I have a mining operation there. How are you planning to reinforce lower arms? and purpose? I like the idea of duel batteries since we have an automatic tranny (no way to push start).

Where are you headed? and purpose?
 
I wouldnt think the Aussie would be a bad idea....especially when combined w/ the pin 7 mod. My biggest concern would be keeping her straight in severly muddy areas.

and on that note.... make sure you get the black wire w/ blue tracer and not the blue wire w/ black tracer:bang:

too bad your not still in NC or i could help you with a winch. If your not needing the protection i like the look of the winchplate snuck behind the stock bumper b/w the framerails, and then your fairlead bolted to the bumper.
 
I am outfitting a 94 FZJ80 for Africa

It already has 3in lift and 315/75 MT and no lockers, someone has suggested that I install a Aussie in the rear... is this GOOD? or BAD? I will be driving on thousands of miles of dirt roads, some of them very muddy.

I would like some help installing the CDL mod...if anyone has done this before... also Looking for a good winch/bumber combination and any other thoughts about what I should do to it before I ship.

anyone do the PHH? I need some assistance.

I will be baseline-ing it, with new oil, plugs, wires, etc.

Thank you in advance;)

By CDL mod do you mean you need the button so you can engage the CDL in high or do you mean the pin 7 mod or both?

By the way jump all over that Aussie Locker and spend the dime on a Warn 8274 if you're after reliability....not my experience but have been told of this winches history.
 
If I understand you correctly the CDL mod allows you to switch the center diff in high and low? and the 7 pin mod allows you to turn off the cnter diff in low? correct?
 
If I understand you correctly the CDL mod allows you to switch the center diff in high and low? and the 7 pin mod allows you to turn off the cnter diff in low? correct?

Just about. CDL switch allows you to engage the CDL in 4H, while the Pin 7 mod allows you to disengage CDL in 4L (with the switch installed).
 
Back
Top Bottom