Boost Fade (Help)

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 19, 2006
Threads
254
Messages
2,013
Location
Tulsa, OK
Website
www.cardomain.com
I am experiencing boost fade of about -1.5psi when the tranny kicks down and the rpm's jump dramatically. The boost won't return to normal until I ease off the throttle or the tranny drops back down a gear. It will hold 6psi all day (regardless of rate of exceleration) as long as I stay out of the major "kick down" range of the tranny; WTF? Has anybody experienced this dilema?

Any input would be greatly appreciated.

Setup:

https://forum.ih8mud.com/showthread.php?p=2298335#post2298335

P.S. I just added a Hallman RX MBC, same results
 
I posted the same thing in the other thread but, I actually experience the opposite; a slight boost bump at kickdown, because more load equals more boost. Are you sure the tranny is not slipping some? This would perhaps workout to less load at the transition and therefore a little less boost. Just a thought. :cheers:
 
Pretty sure not tranny related, but that is a possibility that I hadn't thought of. I've switched to the intake manifold for a signal to the MBC now as oppossed to the turbo itself. I had it this way before the MBC, but not after I insttalled it. Who knows what the culprit is. I'll see if this makes a difference when I get a chance to go for a test drive.
 
Wait! After thinking about what you said, when the rpm's jump drastically, that is creating less load, I think. I don't know, I'm just as confused before.
:confused:

I can only speak to my rig really but at "kickdown" the rpms are jumping aggressively up AND the gear is dropping down one or even in extremes two gears. Those two things equals lots more load. In fact for me to see 8psi on my gauge I almost always have to drop down a gear right at transition to WOT and on a somewhat steep slope. Otherwise 6.5psi is about as much as I can come up with on flats. HTH. :cheers:
 
when the truck down shifts 2 things happen.

1. there is less load on the engine so the exhaust will cool some lessening the ability for the turbo to create boost

2. the increase in RPMs allows the engine to move more air increasing it's demand so to speak of the turbo to maintain a specific boost level.

What is the AR of the turbine you chose?
 
A/R, that's a good question. I have the Warner Ishi off of a 2.3L T-bird. The Garretts that were offered in that application are 48/60 for the auto and 60/63 for the stick. I have heard from various sources that the Warner is even a tad smaller than the 48/60.
I havn't been able to find any numbers on the Warner.
 
I did a search on the web, are you running the waste gate from a nipple on the compressor housing? And if so where are you reading the boost levels?

I was running the WG off of the turbo but now I swapped it back to the manifold. Havn't driven it this way with the MBC hooked up yet.

I've allways got my boost reading from the intake manifold.
 
when the truck down shifts 2 things happen.

1. there is less load on the engine so the exhaust will cool some lessening the ability for the turbo to create boost

2. the increase in RPMs allows the engine to move more air increasing it's demand so to speak of the turbo to maintain a specific boost level.

What is the AR of the turbine you chose?

Again, the sum of those two things equals MORE boost at least on my rig. IOW, apparently the increase in RPMS which equals more air in / more exhaust out / higher turbo temp / higher load once the tranny hooks up, etc. more than makes up for the little loss of load right as the tranny transitions. Again, I only see my highest boost at kickdown and for a few sweet seconds after that, longer if I can sustain some serious load like chugging up a steep slope. I say something's wrong (as an adjustment; not as in anything failing as such) if akarilo is experiencing boost fade at those times. :cheers:
 
I always thought that at any given throttle position engine load decreases with an increase in RPMs.

I was curious if his waste gate was at the compressor housing pre intercooler where his boost gauge was post intercooler and maybe the higher RPMs moved more air via the fan causing a pressure drop post intercooler. No real experience here but I was trying to visualize his setup.
 
In fact for me to see 8psi on my gauge I almost always have to drop down a gear right at transition to WOT and on a somewhat steep slope. Otherwise 6.5psi is about as much as I can come up with on flats. HTH. :cheers:

tangent:

sorry..........

TC are you saying 6.5 is the most boost you can get?

If I lay on it on mine on the flat I have not problem going to the red limit of 9......

same system I'm confused:confused:.
 
I always thought that at any given throttle position engine load decreases with an increase in RPMs.

Nope, increase in rpms almost always equals more load all other things equal. The "exception to everything" here is when engine braking; your rpms can be really high with the calculated load showing something less than idle ... I've seen loads as low as 4% when engine braking but my revs were relatively high. HTH. :cheers:
 
tangent:

sorry..........

TC are you saying 6.5 is the most boost you can get?

If I lay on it on mine on the flat I have not problem going to the red limit of 9......

same system I'm confused:confused:.

No, what I'm saying is simply that on flats or hills heading down I almost never above 6.5psi as long as I'm not kicking down - now if i'm really on it and really stay on it I'll creep to 8psi even without the kickdown but everything except extreme acceleration causing kickdowns is 6.5psi or lower. Now, when I'm heading up hills it is different deal altogether.

Ohh, its the "same system" except for a few things - you've got that beautiful Blitz boost controller, and, you've got a great big tranny that prolly creates lots more load or at least different shift point settings than mine. :cheers:
 
Educated Response

"I would think it's because turbos need load to make boost and you have
less load in the lower gear when it downshifts". Will it make 6 psi in
first or second?

This was Bill Cardell's (Flyin Miata founder) response and I have a feeling this must be the deal. I've been doing business with Bill for a long time and feel his knowledge is second to none.

Thanks for the previous posts that lead the thinking in this direction.
 
Resolved

I got to go for a test drive today and quickly realized that the culprit has been using the nipple on the turbo for wastegate actuation. I switched locations back to the intake manifold (in conjunction with the Hallman RX MBC) and the problem is resolved. There is only a .3-.4 psi drop now, which I can easily live with.

Now if I can get the Dyno guy to call me back I'll be heading there soon!:)
 
I'll have to think about this Shawn, with the throttle position the same and traveling at the same speed if there was a RPM difference then the high RPM would be do to lower gearing, the tranny down shifted. Seems to me that the lower gearing would reduce the load on the engine.

I'm not saying that the throttle position was the same - I'm saying that the transition to WOT (high revs, open throttle) which will induce the kickdown to a lower gear / less load is much more than offset by the increased calculated load caused by climbing revs. IOW the sum of those two things equals much more load, ergo, much more boost (1.5psi more than the normal accelerating max amount).

Another scenario with same more load = more boost observation ... yer traveling down the highway x amount of revs and x amount of load on a flat area, then the highway transitions to a long steep slope ... you can maintain that same x amount of revs if you want and even with effort maintain the same gear for a while with that x amount of revs too if you want, but, the x amount of load will change up and therefore the x amount of boost will change up as well.

Reverse scenario ... going down that thar hill ... you can maintain same revs for a while at least but load will lower and thus boost will lower. Its all the same sorta phenomenon if you ask me. Going back to Akarilo's observations, I'm simply saying, by strictly speaking to my rig, that something seems outta whack with the boost fade; if anything I see the opposite observations as explained above. You just wait till your turbo is running right and you should see that the higher calculated load caused by climbing revs at WOT more than makes up for the lower calculated load of the lower gear. That's all. :cheers:
 
I got to go for a test drive today and quickly realized that the culprit has been using the nipple on the turbo for wastegate actuation. I switched locations back to the intake manifold (in conjunction with the Hallman RX MBC) and the problem is resolved. There is only a .3-.4 psi drop now, which I can easily live with.

Now if I can get the Dyno guy to call me back I'll be heading there soon!:)

good to hear.
 
Back
Top Bottom