Another vibration thread

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 6, 2007
Threads
29
Messages
211
Location
Ogden, Utah
I recently posted a thread about my vibration in the driveline after installing my OME 3" lift. Some of you posted and suggested to replace the u-joints and start there. In doing so, I did find some of them to be bad. I followed all procedures, making sure to mark all yokes and areas. I replaced them as they came off. But, now I have the same vibration and a new vib occur. The vib is at 30-34 mph and the vib comes at 50-55 mph. :mad: I did post a pic of the front DS and all the angles seem to be within 1*. ANYONE have any feed back or ideas to try?:confused: I am wondering though, If I need to install adjustable panhard rods, or dropbrackets for these? I have noticed that the rear seems to be just alittle off inline from the front. I did remove the rear panhard rod to install the kit, but not from the front.
Anyways, any feed back would be great.:cheers:
 
Did you have the shafts balanced? Did you mark the shafts and put them together the way the came off? Did you remove on shaft at a time to see if it was front or rear?


Just need more info as installing the joints wrong, not putting the shafts back in the proper phase or off a spline, and neing out of balance could all cause your issue.
 
I'd get a caster sweep first and make sure that has been addressed properly.

There is no sense in trouble shooting a vib problem when you might not have the caster dialed in yet. Needing more or less caster and then fixing that might alleviate the vib problem.

I think you might have gotten more out of the lift than you think and you are short on caster and the combination has put you in no man's land.

And the need for adj panhards could be a real possibility. The easiest way to check is at the rear. Measure the distance from the frame to a tire lug on both sides and compare.
 
I did not have the shafts balanced, but I did rebuild them correctly and I did mark them. And, as far as the rear panhards, the distance is slightly more on the PS than the DS. I will be taking the front DS out on monday and driving it to see if it is the front DS. Where and how can I do a caster sweep? Is there any info on this? My E-Brake is working great no worries there.
 
I also forgot to mention that I do have drop brackets for the swing arms from MAF. Will I need to put in new CC bushings in them as well?
 
a caster sweep is the technical term for a procedure that is part of an alignment.
My local dealer charged me half the alignment cost because I didn't want him to adjust anything, just give me the numbers.

Right now nobody can tell you what to do about caster until you get those numbers.

BTW, what has MAF given you for advice? I imagine you bought everything there.

Can you put a number on what "slightly more" is?
 
Doing a quick measurement, from the tire tread to the frame, are as follows:
FRONT DS: 12.5"inside tire to the frame
PS: 11.5" " "
REAR DS: 3.25"
PS: 4.25"

I take it, from these measurements that a new adj. panhard is in order?! Anyones thoughts?! Maybe this is the cause of the vib. since i installed the lift?
 
So not correcting the panhards could cause vibration? I thought it was just for rubbing and centering the axle. That's interesting.
 
It's just my theory, but, If the driveline is off 1-2* in relation from the pinion to the tranny, It would be the same if it was 1-2* of in the other direction? Hence, the need to adjust the panhards to realign the axle/pinion to the tranny? I don't know for sure , but it is my theory. I was thinking of this, after everyone was talking about a DC shaft, to correct the problem. Then taking the measurements, made me think about it in the way, instead of up/down, why not side to side as well. Any Thoughts??
 
It does make sense. You just don't hear a lot about people doing panhards to correct vibes. But like you said, angle is angle. Are the driveshafts otherwise in line with each other until the axle moves to the side?
 
Ya know, I just spoke to MAF tech, and we were talking and it is not common for vibs to come after installing the kit. He was running the same kit as me and he has NO vibs. We both think after talking through all factors, that it may be the transfer case. I am going to get an alingment and check everything again to make sure it is tight, and look into the bearings on the transfer case. I did notice some wobble to the flange when I had the ds out. Any thoughts to this??
 
I agree on the cost of "just jumping in". I did read about the 1-2* on the drive shaft and I have not measured them yet, but I am going to get things aligned and have my caster measured as well. After talking with the tech, I am TOTALLY CONFUSED on what to do or look into, this vib is PITA!!!!!!!!!!! I do know that my transmission is slipping and has alot of filings on the magnets, but I just don't know WHAT TO DO?! I am going to get the adj panhards, especially if I want to go next size of tires 33x12.50x15, well anyway I hope that someone has some advise or fix to this problems.
 
the easiest way to measure the drive angles is with a protractor device found at Sears and a socket. You use the socket as a spacer. The socket gets placed on one of the caps of the u-joint and then the protractor is place on the socket.

So basically you rotate the drive shaft so one of the caps is facing down. Place the socket and protractor on that cap and take a reading.

Now rotate the drive shaft 90* and do the same on the new cap that is facing down and record that reading.

Now the difference between those two readings will give you the drive angle of that u-joint.

Read both ends of the shaft and with those two drive angles we can tell you what's going on. Each type of drive shaft has different needs and tolerances.
 
Last edited:
So, I take the readings on just the drive shaft? Or, do I take it on the drive shaft and the flange ends. I think I understand, Landtank you've been very helpful to me and my questions, I owe you some beers!!!!!!!!
 
OK!! after reading again I understand on how to!!!!!!!!!!!! Thanks Landtank, I will take these measurments and post them either tonight or tomorrow. Once again I owe some beers!!
 
Readings

I measureed my DS caster using a inclinometer , here are the readings: I have no idea how to tell what they mean.

FRONT DS (front) 7*(back)7*
rotated (front) 8*(back)8*

REAR DS (front)11*(back)11*
rotated (front)5* (back)4*

I hope this makes sense to someone, Please reply and tell your thoughts. :confused: Thanks John:cheers:
 
Back
Top Bottom