Another Shackle Reversal ???

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 9, 2004
Threads
386
Messages
3,997
Location
Montgomery Co. TEXAS
Website
missionsonwheels.org
This actually started in the Wanted Forum now you fawkers got me started think'n about doing a SR on my rig.

The question is with moving the stock rear hanger to the front and cutting the tube out of old hanger and welding in the frame as a sleeve for the back, how much lift will that add to the front of the rig. I don't want the rig any taller, it barely fits in the garage now. Also would running longer springs, say from a 60 improve the ride or flex at all with this setup?

:beer: :beer: :beer:
 
I did this real quick because I was curious myself. This is not at all accurate (although I did trace the frame from a frame chart). Nuclear's right, it looks like you would lose a little lift - very little. You can see how close the blue line is to the red line in the top picture. Keep in mind that you'll need to use a longer than stock shackle since the shackle mount is in the frame now. I used a 2" longer than stock when I did mine, but I went soa at the same time too.

-Tim

sr_height.jpg
 
By the looks of it your caster angle would be way out in the weeds; you'd have to turn the axle up just to get the stock angle back. Or lengthen the front of the frame. Jack Rice has an excelent article on this subject.
 
Don't waste your time cutting the tube from the from. I got a piece of 1" ID DOM cut to the right size and it works great.
 
Got mine from a local steel and fab shop. Happens to be a great friend that used to run it. We used a magnetic drill press and cut the frame w/ a hole saw. Left about a 1/16 to 1/8 around the DOM for good weld penitration. I did not have my engine in at the time so I ran a broom handle through the DOM to make shure it was squear w/ the rig.

Havn't driven the rig yet so not sure how well it turned out yet.
 
Where can you pick up a magnetic drill press? I guess I could check to see if they rent them? Any suggestions for not using one? Thanks!

Hey 66fj40! I'm working on doing one right now. Do you need some photos? I'll give you a call this week!
 
Nice thing about the mag. drill press, it made the hole squear to both sides of the frame. I have seen them for rent at the usual shops.

I wouldn't try to freehand it but you could. If you hole is a little oversized then you can count on the "slop" to make sure everything is square.
 
nuclearlemon said:
you don't have to fab...just use the rear hanger in the front.
I've heard that before too. It was suggested to that the OEM hanger wouldn't hold up to the abuse of being pounded on the rocks...maybe they meant I drive bad.
DIESEL40 said:
Hey 66fj40! I'm working on doing one right now. Do you need some photos? I'll give you a call this week!
Post up a couple pics, I'm game. We still on for Saturday...the weather is supposed to be awesome...I'm counting on a few warm days this week to my junk rolling again.
phlyfish said:
Got mine from a local steel and fab shop. Happens to be a great friend that used to run it. We used a magnetic drill press and cut the frame w/ a hole saw. Left about a 1/16 to 1/8 around the DOM for good weld penitration. I did not have my engine in at the time so I ran a broom handle through the DOM to make shure it was squear w/ the rig.
With the motor in how would you keep tube square and how vital is it to be square. My front shackles are so bent right now I know the right spring is sitting 1/4 inch inboard from where it should.
 
Back
Top Bottom