2020 CLCC SWAP Meet - Post-it HERE: What are you looking to swap, sell, trade, barter or beg for at the Swap Meet?

[Von Hayek]

I am looking for an Aisin locking hub for a trail spare.

I have a spare tire carrier that was on my 62, but I think I got it off of an 80. I think they are the same (?).

 

[Red703]

Currently on my 1997 Lexus 450, a set of 16 inch rims but one cap is missing of the 4 rims. Tires will not be included, looking to get 250$ I have not idea of the brand they came with the rig when I bought it.

 

[TRFCSUX]

Also looking for a floor mat ?
the big one from the factory that covers the entire floor in the front

 

[Orangejon]

If you don't like paypal, I imagine we can have someone @StaleAle ? There to write up a receipt. Just bring exact change ($25).

ok, thanks.

 

[Crusha]

I'm still planning on coming down from PA.

Anyone need any 80 series specific parts? I have way too many 80 parts in the loft at the shop.

I have a spare set of factory locked axles I can bring down, but I wouldn't want to bring them back home...

 

[76FJ40]

Bring the sun visors for Austin's 80 please.

 

[TRDdrew]

with the purchase of my 80 this weekend and parts car, I have a ton of 80 parts I can bring. 3rd gen T4R stuff, new 5th gen 4runner trail wheels. I post some pics later to see if anyone has any interest

 

[emorth]

What kind of 3rd gen T4R stuff?

 

[TRDdrew]

What kind of 3rd gen T4R stuff?

id have to look, ive parted 3 of them out what would you be looking for

 

[emorth]

Dash gauge panel and fuel tank level sender.

 

[TRDdrew]

Dash gauge panel and fuel tank level sender.

I should have a dash guage panel but negative on the fuel level sender

 

[MDK]

Edit* - Looking for 60 series Aisin carb in working condition, 60 series exhaust manifold+intake

 

[MDK]

(Not cruiser parts... is that ok??)
Anybody interested in this Martin Dreadnought Jr. ? Perfect condition.

 

[Crusha]

I have a ton of 80 parts

What is the color of the parts truck?

 

[1MOA]

Warn coil pack for a vr8000. Has a bad #3 coil. Others test fine. You can use it for spare coils or replace#3 and it will work.
Ended up cheaper to get the entire pack for

 

[wolvesSpareFrly]

I’ve got some Bora hub-centric 1.75” spacers. Never used with hardware. 6x139.7mm lug pattern. I’ll bring ‘em along

 

[L8Shift]

I'm still planning on coming down from PA.

Anyone need any 80 series specific parts? I have way too many 80 parts in the loft at the shop.

We could use the rear passenger side bumper cover. Ours got tweaked a little...

 

[DominicanFZJ80]

I've got a few bits to offer up:

* Midland MXT115 (previously installed, does not have Midland mic mount but everything else needed to install included).
* Pop up shower/toilet tent
* 80 Series Dobinsons Rear Single Rate Springs (C59-313: 4" - 5" lift with 400-700lbs Load)
* Two Person Hammock - Unused
* ...

See ya'll Saturday

 

[Jakes40]

I’ve got some long rear jump seats from my 40. They are in very good condition can bring them if someone is interested.

 

[mdcoa]

Planning on showing up. Will have :

1) A not terribly new at all Arai XD dual-sport helmet I should get rid of (no bike at the moment, and no plans to get one for at least a few years). Free.
2) a never-used 48" hi-lift for sale/trade
3) a weld-in 2" receiver hitch from an abandoned project. Free.
4) An enormous shackle that I don't need. Free.

Looking for--would be interested in some Dobinsons 80/100 series rear springs--I'm running the variable rate (C59-223V) and they're sitting just s bit lower than I'd like when we're fully loaded. . .