1998 LX 470 Front End

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 31, 2018
Threads
3
Messages
20
Location
HBG PA
Hi everyone,

I've been lurking here on and off for a long time. Just took my car to the dealer last week and they want $1,200 to address the upper and lower ball joints (not sure if they will change the arms or the ball joints because I thought it would be irrelevant as I would sell the car), $900 Wheel bearings, and $800 CV boots. I'm not saying that they are a ripoff because they are very reputable and will stand behind their work and parts and it would be hassle free for me. I just can't justify spending that much on a car with 140k miles.

I'm considering taking it to a 4x4 shop but that would mean I need to bring all the parts (or pay dealer pricings). The local Toyota dealer gave me whole sale pricings in the past as long as I email them a list of parts and they don't have to go through and put too much work in it. With my limited technical knowledge, It would be a lot of work just to research all the part numbers needed for this job.

1) Since I'm paying someone to do this, would it be better to just buy new control arms rather than pay for labor to replace the ball joints?
2) Would anyone have a parts list for any of the above jobs please email or post the links? I found the list for Axle job.
3) The dealer also said that the car is not leveled. I did some research on that and maybe because Firestone didn't adjust the torsion bar when I had them do an alignment? Or do I need to address the shocks at this age?
4) Any experienced person here have the time to do these (with pay of course)? Experience with the AHC would be preferable. I actually want to change all the fluids (transmission, AHC, differential) and address the air fuel sensors as well.
5) What would be fair labor for these jobs that I should expect at a 4x4 shop?

I would prefer not having to take it to the 4x4 shop is because I can't find one really close by and if they open things up and figure out that I need more parts. I want to address everything (including the brakes) if possible. I can't ask them to leave it on the lift while I may have to wait until the next day for oe equivalent parts. I do have garage space as well as hydraulic lift with a couple jack stands. I can also drive an hour or two if necessary. Thank you
 
Last edited:
I don't know as I do most of my stuff on my own but I will give it a bump for you. Someone will be along shortly to help you out.

:beer:
 
@Upinhed I think its important to try and find a mechanic who knows these cars. They are not very common.
Here is a mech that was recommended in the past for PA.

Also keep in mind, miles on these 100 series doesnt mean much. The motor, trans and major drivetrain components last a very long time. Dont give up on your LX at 140k, assuming you enjoy driving it. They have a very long service life. Most on the forum have over 200k

upload_2018-6-1_12-32-1.webp
CRUISER MECHANICS - Listed by State
 
Is there an easy way for me to check if my brakes are still good (for another 30k mi)? I put about 28K mi on the vehicle and I'm not sure when the fronts were replaced. I know that the calipers were changed about 35K mi ago at the dealer. There is pulsation when braking but it only happen once vehicle is warmed up so I figure it's the control arms or the wheel bearings?

How about the shocks? Any test to see if they are still good? Would it be less labor to get them changed out now and keep the old shocks (if they're still good) for the next replacement?

@Upinhed I think its important to try and find a mechanic who knows these cars. They are not very common.
Here is a mech that was recommended in the past for PA.

Also keep in mind, miles on these 100 series doesnt mean much. The motor, trans and major drivetrain components last a very long time. Dont give up on your LX at 140k, assuming you enjoy driving it. They have a very long service life. Most on the forum have over 200k

View attachment 1713719CRUISER MECHANICS - Listed by State

I agree about finding a mechanic who knows these cars, that's why I would go with a MUD owner. There's always a chance they may put a trainee (LX470) on my car. I've done brakes (rotors and pads) before on a 2001 honda accord, pretty simple. I've done valve cover gaskets on a 1995 540i before, pretty simple too. The thing is that I saw the gaskets done once by an indie had my brother with me to double check with the instructions as well as 2nd set of hands. I can follow instructions but I'm afraid of hard to remove parts as well as there's so much to be done it would be overwhelming for a first try. I usually don't attempt these things unless I think that I can get them done right the first time.


I don't know as I do most of my stuff on my own but I will give it a bump for you. Someone will be along shortly to help you out.
:beer:

Thank you, since you've done these things on your own maybe you can help with any pitfalls I should avoid? I've spent more than 8 hours since last night doing research and it's a little bit frustrating because many threads tells the OP to go search. And when searching, some of the information is too old. For example, I must've done dozens of searches over the past month about axles and I just found out a couple hours ago (3am) that I should order them from detroit axle.

All the prices seem pretty reasonable to me. 140k is nothing for miles on a Landcrusier.

Thanks. I thought the Wheel Bearings are a bit steep if they are to be done every 30K mi. Aprox how much should the parts cost (repack and replace)?
 
I am new to these vehicles myself, so can't give you to many recommendations. Like others have stated, 140K on these vehicles is nothing. You listed some pricing from the dealer in your original post. I would read and/or discuss with the service writer what exactly in detail the pricing includes. Make sure you are comparing apples with apples when price shopping. You are on the right track by asking questions. Don't get frustrated when looking for help. Their are only dumb answers, not dumb questions.
 
@Upinhed you can refine your mud search fu by being selective with the “posted by member” field. I’m sure you’ve read enough to get a feel for those who add real value to a subject, as opposed to those who just add. For instance for most of what you want to do you could just limit your search to @2001LC posts or @abuck99; for AC stuff then look at @flintknapper, sound system then @jerryb etc. There are plenty of others worthy of mention too, but these guys are just off the top of my head.
 
You need to do a little of your own inspecting. Why are they suggest the upper and lower ball joints? Are the boots cracked and/or are the joints making noise? What about the CVs? Are those boot torn and slinging grease?

Brakes are easy to check, there's a window on the back of the caliper and you can see right into the pad and see how much material is there.

For parts, hit up @cruiseroutfit, he's got the upper and lower ball joints, CV reboot kits, and bearing kits.
 
You need to do a little of your own inspecting. Why are they suggest the upper and lower ball joints? Are the boots cracked and/or are the joints making noise? What about the CVs? Are those boot torn and slinging grease?

Brakes are easy to check, there's a window on the back of the caliper and you can see right into the pad and see how much material is there.

For parts, hit up @cruiseroutfit, he's got the upper and lower ball joints, CV reboot kits, and bearing kits.


The CVs are a sure thing, I had someone injecting more grease into the cracked boots and yes it's slinging grease everywhere. The surprise thing is that it's not the axle that's causing any ride problems - yet?

I think they said that the boots are cracked. If I run over a pot hole or a bump hard there maybe noises (should I)? Ever since I found out the CV boots were torn I've taken it easy. Bobby Rahal Lexus is very reputable so I'm thinking they can't really mess up on these diagnosis? I plan to call them back for more clarification after I'm armed with more information.

I'm adding the cost and I think I may have to skip the brakes because the calipers and pads were changed less than 35k mi ago. I haven't gotten around to price the brake parts yet. The nearby off road shop said that they will only charge $50 more for labor for the brakes.

I just found the vendor section and will sure give them a chance for business as soon as I figure out if I should go with the dealer or not. I'm at ~$1,500 + $900 labor if I go independent shop and maybe the dealer's quote ($2,900) already include peripheral parts that are necessary once they tear into it. They would probably also have it done overnight and they would also provide warranty on labor too. Thank you for your help!
 
@Upinhed you can refine your mud search fu by being selective with the “posted by member” field. I’m sure you’ve read enough to get a feel for those who add real value to a subject, as opposed to those who just add. For instance for most of what you want to do you could just limit your search to @2001LC posts or @abuck99; for AC stuff then look at @flintknapper, sound system then @jerryb etc. There are plenty of others worthy of mention too, but these guys are just off the top of my head.

Yes, this is very helpful and I will apply it in my search. Unfortunately I did not pay attention to names. I pretty much just plow through the thread looking at key words and only read the relevant information. Since my technical knowledge is very limited, every search begets more peripheral searches to help me understand the contents. I wish others would give the same advice because when I searched I saw lots of advice to search and believe me I've looked but it's not easy to dig through all the stuff to get to the relevant information.
 
Are they installing new bearings? or just repacking them?

This is one of the many questions I'm going to ask them when I call them back. They charged me $85 to diagnose, wash and vacuum, plus 2 days loaner which I put almost 400 miles on. They were very busy and I didn't want to bother them too much because I honestly thought I would just take the car to the auction and be done with it.

I actually put it on craigslist for $8,500 disclosing all the faults it has and only got one person telling me that it was way over priced. My brother from TX actually called me a couple days after and said that he and his wife is expecting and wanted me too look for one (under $10K) around my area (he was hooked when he spent one month with it 2 years ago when he visited). After I looked around I realized how clean mine still looks so I told him I would sell it to him for $6,500 plus I will do all the leg work and get the car as much sorted out as I can with his budget. He even said that he's willing to spend a more on mine if needed and even if it costs less to fix he'd still paying me $10K. I'm just going to fix it as if I'm keeping it and I'm grateful for all the information everyone shares here.

I would've taken the car to the dealer much sooner knowing what I know now. The reason I didn't was because I had 2 other mechanics telling me that I don't need to address the front end yet. Even the dealer's mechanic told me that he doesn't feel that something is wrong with the front end on the test drive.
 
I replaced both of my '98 LC's lower control arms to fix bad ball joints and squeaky bushings. They are "simply" bolt on & off, if you don't mind messing with torsion bars, etc. But the arms come with all new OEM bushings and ball joints installed already.

I'm not sure about the upper arms.
 
I had to drive it today for about 15 miles both ways. There were brake squeaks when I backed it out of the garage (not sure front or back) but no squeaks at all driving forward. I could not hear any clink or noises from the suspension with the windows down. It handled bumps and small potholes on the road just fine. I purposely went a little fast over where the road met the parking lot and everything is fine there too. I was a little hard and bouncy over rough roads - and I think it would feels smoother if tfully loaded. I did look under to check out the control arms and I can't tell if the joints were busted or not, they were rusty. Even parts of the shocks were rusty - the part that connects the AHC hose to the shocks were rusty too and it really bothered me so if someone can help me with the part name or number that would be great.


I replaced both of my '98 LC's lower control arms to fix bad ball joints and squeaky bushings. They are "simply" bolt on & off, if you don't mind messing with torsion bars, etc. But the arms come with all new OEM bushings and ball joints installed already.

I'm not sure about the upper arms.

It saves me time that the LCAs come with bushings. I will update my notes. Thank you!
 
Back
Top Bottom