Nice products. Just ordered.
15% off coupon and new prices on my website (1 Viewer)
- Thread starter bhicks
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
- Thread starter
- #102
Thanks for the orders guys. I just got back from a 3 day mini fishing/camping trip with my boys to a favorite fishing spot. I will get all these new orders processed and packaged today and mailed out tomorrow.
- Thread starter
- #104
Been working on the 40 series cup holders over the last few weeks. These are for the ones that came with a center console. I'm not 100% sure what years these consoles came on but they are the only consoles I have been able to track down. Here's a sneak peak of what I will be releasing in September. Here's the single I have so far.
- Thread starter
- #106
Here is the double cup holder/organizer for the larger later years console (had the rear heat under it). I don't have pics of the cup holder installed because it was so brittle it literally fell apart on me. It's just pieces loosely held together with duct tape now. I will do my best to track down another console that isn't in pieces for better pics.
How about an insert for a 100 series center cup holder (the butterfly brackets are always broken or missing) or maybe an organizer for inside the large center console? 
- Thread starter
- #109
I owned a 100 for a couple years and asked around to see if there was interest for this but got very few responses so I gave up on the project. I no longer own the 100 so it would be difficult to make the insert. If there was enough interest and I had acess to a local 100 then I could probably get this project going.How about an insert for a 100 series center cup holder (the butterfly brackets are always broken or missing) or maybe an organizer for inside the large center console?
I must have missed while overseas. I wasn't on as much without a project. Maybe eventually. Thanks for responding. 
How well does spray paint adhere to this type of plastic? This is gonna save me a lot(time and money) and still look stock in my BJ60.
Oh and anybody know what used to be screwed to the sides of my center console (60 series)? Looks like it may have been something to hold the seat belt in place.
Oh and anybody know what used to be screwed to the sides of my center console (60 series)? Looks like it may have been something to hold the seat belt in place.
- Thread starter
- #112
You have to use a spray paint that is specifically designed for plastic. Quite a few of the big Brands now on the market show on the bottle that it will stick to plastic. ABS plastic works well at bonding to paint. Some Plastics like nylon will not accept paint at all. I use ABS plastic for all of my 3D printed parts.
- Thread starter
- #113
40 series cup holders were all released today. You can see them all my website. You just need to scroll down to the bottom of my homepage.
www.bh3dprinting.com
They're also available on my Etsy page which is where i do all international shipping.
www.etsy.com/shop/bh3dprinting
www.bh3dprinting.com
They're also available on my Etsy page which is where i do all international shipping.
www.etsy.com/shop/bh3dprinting
How about an insert for a 100 series center cup holder (the butterfly brackets are always broken or missing) or maybe an organizer for inside the large center console?
Ive been looking for something like this as well the "butterflies" in ours don't stay at all and cups just tip over.
- Thread starter
- #115
Maybe I should look into this project again. It's possible the demand is there now. I need access to a local 100 for a few days.
Last edited:
- Thread starter
- #116
I can't believe in October that I'm already getting questions about Christmas/Holiday promos but I got 3 just in the last 2 days. I will not be running any promo beyond my current mud discount during the holidays. The free shipping and 15% mud discount will run through 1/1/18. The coupon code is "TEQ15" and is good for 2 1/2 more months. I don't think I will be able to continue the promo after that due to the cost increase of filament, shipping, paint, hardware, aluminum, etc. It's seems like EVERYTHING is going up rapidly right now and my profits and getting super small.
- Thread starter
- #117
So Halloween is officially behind us and the holiday rush is about to begin. I wanted to remind folks of two things before ordering. One is that my Mud discount of 15% off the entire order and free shipping is still good through the 1st of January. Coupon code "TEQ15" during checkout. Also, orders may take 4-5 days to process and not my usual 2-3 days due to the increase in orders. Please be patient with me during November and December. Shipping simply takes a little longer during this super busy time. I process orders as fast as I can. I wish I could hire people for the holidays but just can't stomach firing them as soon as the holidays are over.
This is great!!! Not too expensive and serving its purpose.... To hold my coffee. Haha. Just ordered mine. Are you making other types of things for the 60s series?
- Thread starter
- #119
Eventually I plan to release a rear cup holder, a TEQ grille badge, and possibly a cellphone/gps dash mount. I just can't do any new product development during my current busy season. Once orders slow down in a couple months, I will start the design process up again on a bunch of new products.
- Thread starter
- #120
Finally got the updates working properly on my website. Gave the home page a new look. Hopefully it's a lot easier to find specific products now.
www.bh3dprinting.com
Now I need to do the same thing to my etsy page. It needs some serious visual updates.
www.bh3dprinting.com
Now I need to do the same thing to my etsy page. It needs some serious visual updates.
