15% off coupon and new prices on my website

[bhicks]

So it looks like a few people over the crazy busy holiday weekend tried to use my current promo code and got an " expired" message. Make sure to use code "TEQ15". The letters should be upper case and no spaces. I had an old code that was similar that is now expired. The current code IS active and good through the end of the year.

 

[bhicks]

Thanks Bhicks - love this upgrade for my 200.......View attachment 1358412

What badge did you order for your 200 series rear hatch?

 

[RS6tofj80]

it's the oval one you had on Ebay - I had it sprayed black then the raised parts done in body color...

on the 200's rear hatch it's a bit more convex then the emblem so I used a thin layer of 3/8" wide 3M adhesive tape around the edge and it looks oem and is rock solid. it barely covers the 2 centering holes left from the original emblem - so fitment is key

 

[bhicks]

it's the oval one you had on Ebay - I had it sprayed black then the raised parts done in body color...

on the 200's rear hatch it's a bit more convex then the emblem so I used a thin layer of 3/8" wide 3M adhesive tape around the edge and it looks oem and is rock solid. it barely covers the 2 centering holes left from the original emblem - so fitment is key

I have a TEQ badge that is the same dimensions as my universal oval badge BUT with a recessed backside to account for a bit of curvature. It's the 5th Gen 4Runner rear TEQ badge. I bet that would have attached flush with no mods needed. Either way, it turned out great on your 200.

 

[Hkfan7]

Is there still a coupon code or some discount on the cup holders I would like to pick up front and rear for an lx450. I seen there was once one give way back.

 

[bhicks]

Is there still a coupon code or some discount on the cup holders I would like to pick up front and rear for an lx450. I seen there was once one give way back.

Use coupon code "TEQ15" on my website www.bh3dprinting.com
That will give you 15% off the entire order and still allow for free shipping.

 

[Hkfan7]

A new product is on it's way!! Here's version 5.0 of the prototypes. Fitment is perfect. I had to make a few last changes to get fimnent dialed in and a few structural upgrades for durability. It sits nice and snug to the center console with no gaps. Matching that 5 degree slope with a slight bend vertically and horizontally PLUS is tapers at the top was a HUGE PITA, but I finally got it matched. I'm proud of how it turned out. I have now made 3 of these with two more on my printers as I type. I will make a batch of about 10 total over the next few days and get these up on my website by Sunday evening. This can be attached with simply hooking it up top and using the 3 large strips of 3M adhesive OR you can use the screw holes with any 1" coarse thread screw. I made sure this fit on ALL 80 series console. I had to make this in two pieces. The bottom tray is one piece then the double cup/top is the other. I then snap the two parts together and do a 40 minute acetone batch which bonds the two parts into one. There is still remnants of a seam if you look closely but it's not as extreme as the seem you get on injection molding parts. There seems to be two models of center consoles. One with the padded armrest/top and one with a tray on top. The one with the tray on top has a hinge that goes all the way across the rear lid which prevents the "hook" from grabbing up top. I made another design that does not have that hook. It would mount with the adhesive AND screws only. 90%+ of us have the center console with the padded top and the design in the pic will fit that one.

I ORDERED A SET FOR BOTH FRONT AND BACK FOR AN LX450,.. WOW! .. impressive design and well thought out.. little rough on the finish but what the hell it's hand made pretty much!... Definitely beats holding a drink between my legs! THANKS!

 

[Walletclan]

Keep up the good work. I think I am going to get myself one for Christmas.

 

[Hkfan7]

I purchased two, both front and back. For my lx450. I am new to this technology & how they are made, IMPRESSIVE! design on both pc's a ''bit fragile''
But a well a well made product. I am a fine furniture tech, and found them a little rough on the finish, as far as fine detailing to sanding and final coating finish, which I will address. but overall a nice well thought out design and product...Thank you!

 

[Hkfan7]

I purchased two, both front and back. For my lx450. I am new to this technology & how they are made, IMPRESSIVE! design on both pc's a ''bit fragile''
But a well made product. I am a fine furniture tech, and found them a little rough on the finish, as far as fine detailing to sanding and final coating finish, which I will address. but overall a nice well thought out design and product...Thank you!

 

[bhicks]

Just a heads up to anyone planning on putting in an order before Christmas. We will be heading out of town from 12/18-12/29 visiting family in Colorado. Any orders that need to be shipped out and delivered by Christmas must be placed by this Thursday 12/15 in order to be shipped out before I leave and delivered before Christmas. No orders will ship out during the dates we will be gone. Orders we resume shipping out on 12/30.

 

[bhicks]

We got back from Colorado last night. We will be unpacking today and will start processing this mtn. of orders this afternoon. I will start shipping out order tomorrow. They will ship out in the order they were placed. Should take about 3 days to get all orders out that came in from 8/18-8/28.

 

[bhicks]

I wanted to give a heads up to the 70 series guys. I am officially starting the cup holder development for the 70 series crowd. I have a lot going on so it will be a semi slow development, but I should have some prototypes to show off in early February.

 

[revkev]

Just got my cup holder for my 62! Its the most I ever spent on a cupholder, but this is a solid piece of work with very practical slots and worth it. Love the "Land Cruiser" detail too. Great job!

 

[bhicks]

So the 70 series cup holders are now out. I decided to go with another mud member for shipping out the product. I will just be the manufacturer on this one. If you need a double cup holder for your 7x Series Landcruiser then head over to the Odd Iron Off Road guys. We offer cup holders for the center console (if you have one in your 70) and the floor mounted cup holder for the 70 guys that don't have that tranny hump center console over the shifters. here's the product link:
STORE

 

[Steilm]

I recently launched my website and to promote it I'm offering a 15% off coupon (coupon code "bh3d15"). I am also offering free shipping through the rest of this month and have been able to lower my prices on almost all of my products. I found a new vendor for the 3D printing filament that sells the quality American made "PRO" grade filament for a much better price. I am now able to pass that savings on to my products. I have all TEQ badges and cup holders in stock right now. The site is www.bh3dprinting.com.

I have to check that 3D printing filament of yours coz our company is been looking for a steal price but best.

 

[bhicks]

I have to check that 3D printing filament of yours coz our company is been looking for a steal price but best.

I use the dockwell brand from www.pcrush.com Their pricing is fantastic for the quality. It's not the best stuff on the market, but when you factor in the price; it can't be beat. Their black ABS prints the best. Their lighter colors like silver, gray, and white don't print as well. I just use their black 1.75mm ABS for all of my ABS needs. I have gone through almost 5,000 spools of the black over the last 4 years. Other than Walmart, I'm pretty sure I'm their 2nd biggest vendor for the black.

 

[bhicks]

Thanks for all the Father's Day orders. Things have finally slowed down again. Heading out on Saturday for 7 days of camping with the family. If you want to place an order and have it shipped before I leave then it needs to be placed by this Thursday. If not, it will get processed when I return on July 1st.

 

[Walletclan]

Ordered! I should have ordered years ago.

 

[joez]

Ordered during the holiday week, and they just arrived this morning. Awesome fitment and quality, having a passenger side cup holder will make the 1400 mile drive to moab slightly more bearable for my wife. Looks like I'll be ordering for my 3rd and 1st Gen 4runner's next!