part

I have been searching on mud and different parts catalogs and getting conflicting info. Does anyone have the part number for the front driveshaft rear u-joint part number? Is it better to just replace the entire driveshaft or are we good to replace just the u-joint? Thanks a bunch

Hello, Dummy question, but just want to make sure before moving on. I'm ripping out the rear AHC shocks on my 2000 LX470 and on one side this part came off: But on the other side it stayed attached to the frame: To be clear this on the underside of the shock mount. The lower of the two top...

I am looking for a new or used bracket for the rubber extension on the rear passenger door flare. Is there a part number for the Bracket itself or is it a complete assembly with the rubber extension? If complete, is there a part number for the passenger side rubber extension? I've check all...

I am replacing my valve cover gasket and while wiggling out the Half Moon pieces both of them broke on the outside edge (my luck)......I need to order 2 replacements, can someone help me with a part# or the actual name of the pieces so I can locate them. Searching via "half moon" seems to get me...

Would also like the bracket if available.

Got these with a parts lot: they are 555 brand. Part number is stamped on the drum. I couldn’t use them for my project, because the studs were too short for the extra thick mounting face on these. They are extremely heavy duty…. And will be heavy to ship…. 100$ plus shipping

Does Toyota sell individual interior wood trim replacement pieces? If so, can anyone provide a part number to order the passenger side trim pictured below? Thanks in advance.

Hi, Whats the part number for the metal gasket for the oil pan drain plug for the fj 60 and fj62? Not the fiber one. Thanks, Mike

I've searched here but can't find the heater tee part number. Toydiy shows the tees but doesn't provide a part number. Dealer says I gotta buy the hose kits (three hoses plus tee) to get the tee. The tees look fine and I'll take them apart to inspect before I just replace. Just wanted to...

I was expecting to use some sort of glue to attach this, but it has double-sided tape already applied. How long do you apply pressure for before it is safe to drive without it falling off?

Hello all, this is mounted under the distributor of a 1979 2F. I’ve never seen one but likely somebody knows what it is? It has apparently been disconnected for some time but it has a set of hefty bolts attaching it to the block and some odd passage connection further up into the block

Seeking a part time kit for a 1990 Hdj81. After a marks4wd set up that someone didn’t get around to installing. I believe pre-94 doesn’t require any modifications to run the Aisin hubs. Lemme know if you have a kit you’re willing to let go. Located in Northern California(grass valley) but can...

Bought some tools and this came with it. Hatch cover?? Was advertised as 4Runner tools, but who knows : )

Maybe we need a 3D Printed Parts for 80s thread. A thread where every 3D printed part available is listed or ideas for new ones are shared. The following are two ideas I have for 3D printed parts. Maybe Outsane or someone else could take these on. 1) Replacement caps for the headlight level...

Looking to buy Part# 87208-60270 - Pic Description. 80 series /1997 - PIPE SUB - ASSEMBLY, WATER. PIPE, HEATER

I mangled this Heater Inlet Pipe changing out my Heater control Valve and associated hoses.......I need/want to replace it, anyone have the part # handy, I tried to find the dang thing without success. I "THINK" it may be Part # 87208-60260, but hoping to get verification here before buying...

Had to remove taillight (someone dropped bulb inside and it was rattling..) Ripped seal (part of it stuck on a back door). Doesn't seem like it's available as a separate PN?

Hey yall, 93 HDJ81- found my alternator output low. Brushes are extremely worn, ordered part (looked up part # on jp-carparts to make sure had correct part # for my import) from local toyota dealer and it's a bit different. My old brushes didn't have the plastic housing around the brushes and...

Hey everyone, I am putting my Instrument cluster back together and I can't find the small part that holds the needle of the temp gauge. I must have dropped it before it made it in to my ziplock but now I cant find it. Any ideas on how I could make something that will do the same thing or where...

hello i need a beige carpet floor, if its a piece it can be from any part of the floor inside truck. as long as it is beige. need to cover a hole. any help would be great