Selling a pair of birfields removed from a running 96 80 series. No clicks or noises from the front axle grab a cheap spare or two. Birfs $50 each buy both for $90. Also have the inner axle shafts they look great all splines are nice and straight and the seal surfaces are good. Either side $35...
Knuckles, Hubs, Birfs, Shafts, Housing, end caps, calipers, etc.
Let me know what year your cruiser is. Shipping for Axle Housing not available unless you are using someone's shipping account and make your own arrangements.
Most of the axle parts can be shipped in USPS flat rate boxes.
Send PM...
So Cal BIRFIELDS for 93-97 ARE SOLD, NICE PAIR OF SHORT BIRFS NOW AVAILABLE, $100 EACH INCLUDING SHIPPING.
Backing plates, Spindles, Axle Housing, Tie Rod, Axle shafts , Drive flanges, Relay Rod (Drag Link), Sway Bar, ETC ETC ETC
Parts available for 91-97 Cruiser or LX series.
From a 1997...
Hi guys, long story short, I had a major failure of my brake hardlines this past weekend driving to a camping trip. Lots of smoke from the caliper area. After we towed the truck home we started tearing apart the knuckles to change the seals and overhaul everything, (I had noticed my seals were...
I'm doing my knuckle rebuild on my 97 fzj80 now and when I pulled out the axle the tone ring fell off. This happened last year and I had a mechanic replace it. When I put it back on it just slips all the way down with nothing to hold it there. Birfields are 2 years old. Any idea what could cause...
Hello All,
I have an 80 series Landcruiser, 1992, RHD, Diesel, and the birfields were replaced about three years ago (and wheel bearings packed). I've put on about 30k or so since. I have no issues. I'm looking for advice about regular birfield maintenance and wheel bearing maintenance. How...
Pulling my front axle apart on my 97 with 250k, which had been supposedly serviced few times but this is the first time I have been in it.
The first thing I noticed was the knuckle was full of “birf soup” (gear lube and grease), so my seals are shot. They were getting replaced anyway.
What...
My 97 is sitting in the garage, rear hub torn apart as I replace the rear hub bearings and seals. I plan on replacing the hub studs. I am trying to figure our whether to stick with OEM or try one of the Trail Gear kits? Right now my drivetrain is stock and on 34x10.5 BFGs.
I live 3 hours...
After doing birfields, I also replaced the TREs now Ive been gearing up for a long distance road trip so Birfields drove it fine, replaced TRTEs and now it pulls to passenger a bit. BUT to be safe I rechecked wheel bearings and they seems good to go. ALL KOYO bearing and races.
Installed my first sets of Birfileds today. Started this morning, checked with Jonesys gargage vid a few times, and she is done. terrain tamers sent me everything gaskets, races Koyo bearing the works. I was nervous but killed it. done and done. And discovered front calipers were junk, so new...
Ok did the rear rotors yesterday and Im starting birfileds tomorrow my question is where can I get the brake lines that go from caliper to axle all 4 of them .
Never done Birfs in My life, But Im going to do them anyway. Unbelievable how fast these arrived. Now I have to tear it down. Any tips,tools etc all input is welcomed. Im not a pay a stranger that dosnet love the truck they are working on, so with a lot of youtube help(powermodz) and the FSM Ill...
What tools will I need to complete this (both sides) I want to hit this running and get her back on 4 wheels asap. So what will I need to start to finish the birfs. Ive built Bikes Jeeps and houses, So I have to ask.
Thanks In advance.
Just took My rig out to the extreme off road park in upsate NY and after noticing a slight bird like squeak while truning and driving out there, while I was in the park. Had her in CDL then 4 hi 4lo the usual, after not too long i got the birfield clicking on the drivers side, Now since this...
I have a pair of fine spine birfields which have been spares sitting in the back of my garage for 10+ years. I'm concluding I'll never use them, as I have long fields in everything I own. I believe they came out of a 1983 mini truck.
In good shape, except for the surface rust on the outside...