Complete PTO Rebuild thread

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Mikesta

Never decruiserfied
SILVER Star
Joined
Jan 28, 2005
Threads
393
Messages
3,796
Location
Missouri
Website
www.showmerents.com
Hi everyone. I usually hang in the 45 boards and rarely come here but I figured this is where this thread should go. Let me know If it should go somewhere else.

I have 2 PTO (power transfer output) units that connect to the transfer case. I am in the process of completely rebuilding one of them.

I've cleaned all the parts and need to replace O rings and Gaskets. The bearings are in suprisingly great shape. I don't think this PTO was used much.

I have a few questions for those that have gone this road before.

1. Where did you get your parts. I've only found some on SOR but they are last stand.
2. What manual did you use. I have a original body manual for the early cruisers that I'm using with 13 steps assembly/dissassembly. Is this the best guide?

I will have more, but right now here are some pictures.
MVC-903S.webp
MVC-905S.webp
 
Contact Cdan when he returns from Moab and see what is still available from the dealer....

I have replaced lip seals but have not ever had a reason to remove the other shaft...so I do not know if you will be able to find the orings for that other than possibly at a oring/seal shop...


Good luck!


-Steve



Good luck!


-Steve
 
Output shaft seals are available from Toyota:

PTO Front and Rear Seal 90311-35004

Only know this because its the same as the transfer case rear output seal on the 25. ;) Most of the PTO's I've dealt with really only needed these seals replaced anyhow.
 
Seal Source in Portland OR will have your o-rings if you can't find them OEM , I can order them if you have a size. need to know the smallest diameter of the groove, the shaft diameter and the od of the o-ring itself usually you can get by with a shaft diameter and a oring cross section diameter. we stock some metric o-rings, so you might even be in luck. probably just a few cents cost.
 
I could use this information too, but for the winch head as well...I'm not going to be tearing into mine until at least fall, but if there's nothing like this up before I do I'll try to do it.

I don't have the luxury of that chassis manual...Any chance of a scan of the PTO stuff?

A list of part numbers for 3rd party manufacturers would be insanely great.

Thanks! Good luck!
 
Poser said:
Contact Cdan when he returns from Moab and see what is still available from the dealer....

-Steve

Will do. Check.

Cruiser_Nerd said:
PTO Front and Rear Seal 90311-35004

Thanks!

FoYoChe said:
Seal Source in Portland OR will have your o-rings if you can't find them OEM , I can order them if you have a size. need to know the smallest diameter of the groove, the shaft diameter and the od of the o-ring itself usually you can get by with a shaft diameter and a oring cross section diameter. we stock some metric o-rings, so you might even be in luck. probably just a few cents cost.

Good to know FoYoChe. I will keep you in mind... thanks.

Advent said:
I could use this information too, but for the winch head as well...I'm not going to be tearing into mine until at least fall, but if there's nothing like this up before I do I'll try to do it.

I don't have the luxury of that chassis manual...Any chance of a scan of the PTO stuff?

A list of part numbers for 3rd party manufacturers would be insanely great.

Thanks! Good luck!

Advent, I believe you can download the PDF off of Root45.com I don't know if its the same one, but I think it is. Cruiser_Nerd has 1 part # so far... actually 2 part numbers.

#3 Question for those that have done this... or for those with more common sense. I think the bearings just use the case oil.. Is this correct or do I need to re-pack these succers. I know... RTFM. I'm planning a Memorial service for my Son.. this is just a break.
 
Mikesta said:
Advent, I believe you can download the PDF off of Root45.com I don't know if its the same one, but I think it is. Cruiser_Nerd has 1 part # so far... actually 2 part numbers.

Just looked, I found the manual for the FJ45, but not the PTO.

I was wondering about 3rd party parts because I have this odd feeling Toyota might discontinue or run out of FJ25/PTO parts sooner rather than later :frown:
 
You will find almost NOTHING available for the PTO or winch head from the dealers. Here in Guatemala I've been able to find the seals and bearings aftermarket and any busted machined parts I can have made relatively cheaply because of the labor costs here. You'll be making your own gaskets but that's not a big deal.

When you tear into the winch head you'll find the large worm gear is likely worn quite a bit.
 
Ok, I found step by step instuctions in another manual . Its

"TOYOTA Land Cruiser Repair Manual" Aug. 1980. Pub. No. 36044E."

You can buy it from SOR. But I'd look elsewhere first.
 
FWIW,
There is a Toyota wrecking yard here in Portland Or. TOY MAN.
http://www.thetoyotaman.com/
There is a PTO winch mounted on the front of what looks like a 60's era FJ40. It has the split hood with the chrome hood trim. The rig is in really rough shape, however the winch looks good. I didn't see the throttle handle when I looked in the cab but I might have missed it.It does have the shaft in place (I could see it route under the radiator and went back under the frame). I don't think this guy really knows what he has as far as the winch value. I bet someone could pick it up pretty cheap.
 
Colorado Boy-74-FJ40 said:
FWIW,
There is a Toyota wrecking yard here in Portland Or. TOY MAN.
http://www.thetoyotaman.com/
There is a PTO winch mounted on the front of what looks like a 60's era FJ40. It has the split hood with the chrome hood trim. The rig is in really rough shape, however the winch looks good. I didn't see the throttle handle when I looked in the cab but I might have missed it.It does have the shaft in place (I could see it route under the radiator and went back under the frame). I don't think this guy really knows what he has as far as the winch value. I bet someone could pick it up pretty cheap.

He wants $300 for it.

Here are some pictures of the PTO instructions/destructions in the manual I have.
MVC-001S.webp
MVC-002S.webp
MVC-003S.webp
 
He wants $300 for it.
[/QUOTE]
Then why is he letting it rust all to hell sitting in his yard. He should give a s*** if he wants that much for it. Sorry for leading you on. I didn't know.
 
Colorado Boy-74-FJ40 said:
He wants $300 for it.
Then why is he letting it rust all to hell sitting in his yard. He should give a s*** if he wants that much for it. Sorry for leading you on. I didn't know.[/QUOTE]

Thats a good price if its PTO to Winch and all in between. I'm trying to get it all for that. Unless someone else wants it. I really don't need it... but 300 is a good deal for everything.
 
Mikesta said:
Then why is he letting it rust all to hell sitting in his yard. He should give a s*** if he wants that much for it. Sorry for leading you on. I didn't know.

Thats a good price if its PTO to Winch and all in between. I'm trying to get it all for that. Unless someone else wants it. I really don't need it... but 300 is a good deal for everything.[/QUOTE]

Hey Mikesta, how about picking it up for me and I'll pay you back when I pass by in June and I'll give you my ball and claw parts for your trouble? I'd like it for the FJ45LV.
 
Sure........with credit. ;) Disclaimer............that TSB is dated 1961, so the setup is for the early model three speed...............no idea if it makes a difference. :D
 
Cruiser_Nerd said:
Sure........with credit. ;) Disclaimer............that TSB is dated 1961, so the setup is for the early model three speed...............no idea if it makes a difference. :D

I'm going to type up all the text from that. I just cropped out all the images and changed them back to white. MUCH better. Just need to get my site's gallery set up so that I can throw them in there easier.

Thanks!

Here's a teaser:
fig24.jpg
 
Last edited:
Back
Top Bottom