Recent content by Visceral

  1. V

    275/70R18 in spare tire location

    Well, yeah, but that's the most expensive (but obviously nice) solution.
  2. V

    275/70R18 in spare tire location

    I've got the one that integrates into the rear bumper. When you put a bike rack or ball/stinger into the receiver, the stinger or rack protrudes into the space that the larger 275/70r18 wants to take up. I can make it work, but it's not especially easy or straight forward. With bike racks...
  3. V

    Heavy Duty AHC Rebuild

    I love my AHC too, but I would *seriously* consider a spring/TB refresh before spending extra money on the AHC yet. Several posts in the forum detail how to replace the AHC fluid with new and bleed the system. Then with a Techstream setup, adjust the tortion bars to get the AHC well within...
  4. V

    275/70R18 in spare tire location

    Either size makes it very difficult to put a receiver in the factory hitch.
  5. V

    2-2.5" AHC Lift Using King Coils & Shock Spacers

    Unless you have a bumper and winch, my experience is that cranking the stock torsion bars is enough. The first post mentions new sway bar endlinks, I think... that's never a bad idea.
  6. V

    2-2.5" AHC Lift Using King Coils & Shock Spacers

    Often the King Springs are enough. You have to get a reading on the AHC rear pressure and find out if it's enough in your situation for your desired height. With a RTT, rear drawers, a fridge, and a trailer, my truck's rear pressure is up at 8 with just the King Springs, so I'm adding 30mm...
  7. V

    First trip to Hollister Hills in my LX470. Great trip. Lessons learned.

    That looks like a lot of fun, and something I'd love to try out. Stretching the LX's legs in a controlled environment sounds like a much more stress-free way to do it. Also, cheers from another Portland LX :)
  8. V

    The OFFICIAL clunk/thunk driveshaft thread

    A simple hand-pumped model from Amazon with a flexible nose is much easier to use. With a pneumatic, I'd have to swith on the compressor, run the line out to the truck, etc. The hand pump model is pretty easy and doesn't exactly tax muscles.
  9. V

    The OFFICIAL clunk/thunk driveshaft thread

    At this point, and after quite a bit of troubleshooting, I'm convinced that my rear upper control arm bushings are seriously contributing. MetalTech is local, so I'll see if they still have the upper and lower arms. Doesnt appear on their website.
  10. V

    Thorley shorty headers on a pre-05?

    And I wonder why the #2 primary has to be so long on the 98-2004 ones... strange looking design.
  11. V

    Thorley shorty headers on a pre-05?

    Presumable an AIR injection pump (a filtered fresh air pump). AIR pumps run when cats are not yet hot enough to work effectively. The addition of oxygen to the exhaust somehow both increases cat effectiveness and lights them up more quickly. Secondary air injection - Wikipedia I'm not sure...
  12. V

    Thorley shorty headers on a pre-05?

    Do they not fit?
  13. V

    Steering rack story

    We all seem to be having issues at 14X,000. I just had mine replaced after steering became difficult at various angles. Also replaced the PS pump, but the new reman pump is noisy, and I'll probably put the old one back since the new pump made no difference. I had my Lexus rack replaced with...
  14. V

    LX470 Turn Signal/Marker Light Conversion Help

    The instructions above are correct, and unfortunately there appears to be no better way forward than to "just do it". I didn't have any trouble performing the conversion (a poorly placed branch took out one corner light and the 2003+ LX lights are impossible to find). The clear Depo LC corners...
  15. V

    Led bulbs for DRL/High beam and blinkers

    I have the non-X version. It doesn't work for the exact same reason.
Back
Top Bottom