Recent content by redlandcruiser

  1. redlandcruiser

    LX470 Subwoofer Isolation Foam

    I asked the supplier of the foam and they said this: > You are beyond foam repair. That orange corrugated disc is the spider and it’s not supposed to be disconnected. It also looks ripped. Unfortunately you’ll have to replace this woofer. They don’t make the other parts you’ll need to rebuild...
  2. redlandcruiser

    LX470 Subwoofer Isolation Foam

    Yeah, it looks like it was. But that cylinder fits in the little gap which allows it to move up/down, so not really sure where to glue. Chatgpt hasn't been much help either. I see I can get a new one for about $200. Or maybe a different set that's not 25 years old lol
  3. redlandcruiser

    LX470 Subwoofer Isolation Foam

    I think I messed this up. This is my front drivers side speaker. I just glued a new surround on after lining the cylinder thing up in the slot, and now I still hear the scratching/vibrations with medium bass. I looked at several videos and have not seen one where this part was broken. Is this...
  4. redlandcruiser

    How To: 100 Series Hood Lift Support

    Installed these ones today, they're great. However the thick part for me was previously installed at the bottom and I copied that, so mine are upside down lol Should I change them
  5. redlandcruiser

    LX470 ML with no low end sound

    Ah, that works too. I think voice coil replacement or repair is much more difficult if not impossible lol. This wire fix should take about 5 min so hopefully this holds up!
  6. redlandcruiser

    LX470 ML with no low end sound

    I just refoamed my sub and it started being flaky after probably over using it. When I press down it works too. Any leads on replacing the voice coil? Edit: Did some more testing, looks like it's the ground tinsel lead which is a cheap fix. Ordered the simply speakers speaker flex leadwire...
  7. redlandcruiser

    Wanted California: 2001 Lexus LX470 Riverrock Green Mica Front Bumper - UCA76 Med gray

    Looking for a bumper in UCA76 Med gray. I have a bumper that has been beat up, I sanded it down and used bondo many years ago but it doesn't look great, and the color doesn't match at all. I am assuming that a new paint job will be "too fresh" and wont match the rest of the lower trim, so...
  8. redlandcruiser

    LX470 Subwoofer Isolation Foam

    I'm not exactly sure I understand. The gap was because there was like a plastic ring that needed to be removed too, that was glued on top of the previous foam. I took that off and it was a perfect fit. When I hooked everything back up, it sounded wonderful. A few weeks later on a road trip, I...
  9. redlandcruiser

    LX470 Subwoofer Isolation Foam

    Did you see a space between the cone and surround when gluing the new surround on?
  10. redlandcruiser

    2001 LX470 ML Sub Repair

    Finally got around to attempt the ML repair on the rear driver side sub, but this repair kit does not seem to fit... Here is where I am at: When placing the replacement surround on top, with the dimensions: outer diameter=6 1/8" inner diameter=4" cone diameter=4 3/8 The outer ring of the...
  11. redlandcruiser

    Headlight removal, 2001 LX470

    Update: I snapped the passenger side trim. Rip.
  12. redlandcruiser

    Headlight removal, 2001 LX470

    How were you able to work them in/out with that trim on? Mine feels like it’s about to snap, I don’t know which way you would even try to pull it.
  13. redlandcruiser

    Headlight removal, 2001 LX470

    How were you able to work out the headlight unit? I feel as if the trim is going to break, and can’t for the life of me figure out how to remove if
  14. redlandcruiser

    How to wire aftermarket Halo DRL to 12V Circuit

    Wow I didn’t know this. What I want is for the the lights to behave exactly how the OEM lights do. They can all be off, or I can turn on/off the main lights by turning the left stick. If I just wire a the middle halos (where the high beams are) with the 12V does this mean my “high beams” (the...
Back
Top Bottom