Recent content by lazarus18

  1. lazarus18

    Build 70 FJ40 (Here we go!)

    I feel like I’m cheating lol. Gotta keep the ole 3 speed to teach these youngsters how to drive and have some fun down at the ranch!
  2. lazarus18

    Build 70 FJ40 (Here we go!)

    I fully agree with you on all of this. Since I was going to do the throw out bearing, I figured just do a whole clutch kit since I’m in there already. At the same time I will inspect and adjust the pedal and so forth. I did watch a few videos on adjusting everything and I will also use the page...
  3. lazarus18

    Build 70 FJ40 (Here we go!)

    Correct, I have shifted motorcycles, heavy haul trucks and others without using the clutch. It allows me to shift gears but it just ends up coasting to a stop and if I use the accelerator it just revs the motor.
  4. lazarus18

    Build 70 FJ40 (Here we go!)

    That’s where I started, no leaking fluid anywhere and that all seems to be functioning. I might end up just replacing that also though since I’m doing the clutch kit.
  5. lazarus18

    Build 70 FJ40 (Here we go!)

    Yes, I agree and have considered that as well. My pedal does indicate that could be the case. However, if that was the case it wouldn’t allow me to be driving all the way into 3rd gear for 10 min or so and then randomly go out and not function at all and then the next day start working again...
  6. lazarus18

    Build 70 FJ40 (Here we go!)

    It goes in and out of the gears while off. I have not however reached up into the clutch fork area. I’ll do that today.
  7. lazarus18

    Build 70 FJ40 (Here we go!)

    I checked and all good on that side of things. Upon further inspection, my fuel pump seems to be going bad. I could not get it started and checked to see if it was throwing fuel by removing the fuel line from the carb and putting it into a jug and no dice after multiple attempts. I rebuilt it...
  8. lazarus18

    Build 70 FJ40 (Here we go!)

    I will verify.
  9. lazarus18

    Build 70 FJ40 (Here we go!)

    What a guy! I was actually looking at a clutch kit just now lol. I think my problem is 1. My pedal is not correctly positioned as it is stiff at its highest point with no play. 2. I think it’s not catching on the flywheel. More than likely I will end up pulling it, replacing the throw out...
  10. lazarus18

    Build 70 FJ40 (Here we go!)

    Ok, still going over a few things however, I noticed the clamps holding my heater hoses together by the firewall were loose and water came out of them and got pretty hot while driving in the neighborhood trying to flush the radiator. Got those tightened… I was talking to a friend who has a few...
  11. lazarus18

    Build 70 FJ40 (Here we go!)

    I’ll be checking the spring and rod in the morning. I’ll report back with what I find. Appreciate everyone! Also, had a lady say nice jeep… we know how that went and turned out. I also had a guy in a jeep look at my son and do the notorious driving by with his head turned all the way around as...
  12. lazarus18

    Build 70 FJ40 (Here we go!)

    That is correct. If I am reading this all correctly, it sounds like it might be stuck in 1st gear even though the shifter goes into other gears just doesn’t do anything?
  13. lazarus18

    Build 70 FJ40 (Here we go!)

    Checking on that and will report back! It was fine and working… until it wasn’t but glad I was to the neighborhood vs the main road through town. Gary P. Nunn kept me calm though 😂
  14. lazarus18

    Build 70 FJ40 (Here we go!)

    Spoke a little soon… got back to the neighborhood and it seems to only want to drive in 1st gear. In 2nd and 3rd it is creeping and almost like it can’t catch up. I parked it and then noticed while it’s in neutral it won’t move by attempting to roll it. Any ideas? I do know I have a throwout...
  15. lazarus18

    Build 70 FJ40 (Here we go!)

    Holy cow, what a story! Tyler is known for their medical for sure. Glad it turned out better than it could have been!
Back
Top Bottom