Recent content by denbeigh

  1. D

    Rear shuttering and squeak

    I believe it was a 12mm and 14mm socket ratchet extension and ratcheting wrench. And a can of kroil. I did snap a bolt and had to drill and retap but that’s another story. hardest part was figuring out what pieces went where, so I took one linkage off and matched it with the new stuff. It says...
  2. D

    Rear shuttering and squeak

    Doing the bushings is easier than changing the oil. I did mine and it took me a few hours. If I did it again I could do it in an hour.
  3. D

    Rear shuttering and squeak

    I sprayed it a year ago and again this week. Not sure if it’s internal or external but it hasn’t really fixed anything. I think tightening would help but I’m afraid that would engage the brakes. Could you upload a video of your squeak while driving?
  4. D

    Rear shuttering and squeak

    After replacing the sway bar bushings I realized the e brake makes noises when pulling on the cable. When I go over bumps it sounded horrible. When I pull on the brake while going over bumps the noise stops. Is there a way to fix this? Assuming tightening the cable might work?
  5. D

    What have you done to your 100 Series this week?

    Ended up doing a m8 helicoil. First time doing this, i went a little too far past and had to cut the tab. It was a bit of a struggle threading the bolt in after that. I’m afraid to remove the bolt now. Is this helicoil permanent? I imagine I could pull it out with needle nose and rethread...
  6. D

    What have you done to your 100 Series this week?

    I tried extracting it. Wouldn’t budge, wasn’t even rusty. I ended up drilling it all the way through and still the threads remained, reamed it a bit. I put a bolt and nut on. I may go back and tap it one size up, but will this suffice?
  7. D

    What have you done to your 100 Series this week?

    front and rear bushings, doesn’t ride like a boat now, wish I did this sooner. Also did front rotors pads and bearings which was a new experience. Snapped one bolt off, no luck trying to extract it.
  8. D

    Front stabilizer lollipop link

    Thanks for those part numbers. I ordered off a list based off a users post here. There were so many separate parts it was hard to keep track, had to reuse some hardware. The ones I pulled off had a tack weld on the inside. Do you know the torque specs? Also the rear bushing with the linkage...
  9. D

    Front stabilizer lollipop link

    Did my bushings this weekend and the old link had the washer welded on, the new one didn’t come with any washers I so reused one, but what’s the deal with the welded on piece? Is there a way to order a washer kit?
  10. D

    Brake job parts list?

    So my flange studs and nuts are most likely reusable? That would save me a few bucks. Thanks for the write up. I watched a few videos and it seems straight forward, just a lot of pieces.
  11. D

    Brake job parts list?

    Dealer serviced its whole life, averaged about 35k miles for some kind of brake service over the course of 166k miles. I’d think if there was a problem the dealer would have caught it in the last 20 years.
  12. D

    Brake job parts list?

    is the spindle gasket and dust seal necessary or just a precaution?
  13. D

    Brake job parts list?

    looking at the service records the dealership put the rotors on a lathe 30k miles ago, they look like a vinyl record. the rear ones were replaced not too long ago and will only need pads. as far as the bearings go, i have 175k miles, i figure it will be a while before i replace the brakes...
  14. D

    Brake job parts list?

    I plan on doing my brakes and want to make sure I'm not missing anything before I start the job. my list so far cruiserteq front bearing kit snap rings just in case rotors pads 12 cone washers pad retaining clips (do the pads come with these)? do i need new bolts and washers to go along with...
Back
Top Bottom