Recent content by daohaus

  1. daohaus

    Finally started my extruded aluminum drawer system.

    i love that this community is so tight that people know who's selling :)
  2. daohaus

    Finally started my extruded aluminum drawer system.

    I finished most of it and then happenstance occurred and I have to sell the LX. HOWEVER, the drawers are for sale and the new buyer that's flying in needs the space for his in coming new baby. So it's for sale, I just have to get around to posting it in the classified if anyone's interested
  3. daohaus

    Finally started my extruded aluminum drawer system.

    Valid point about have the drawers so far back. I could move it towards the rear a bit. I do like your idea about cutting the wings in half. I might just do that. Thanks!
  4. daohaus

    Finally started my extruded aluminum drawer system.

    Update: worked on the drawer face and finished off the wide wings. Something i didn’t account for when the wings open they hit the rear seats because the rear seats are somewhat reclined. So i had to cut off a couple inches on that end to get it to clear. Question for the right wing I’m...
  5. daohaus

    Finally started my extruded aluminum drawer system.

    Almost there. I installed turnbuckles secured them to the body. I slapped the roof and said this isn’t going anywhere. Now to mount the top and some wings for the sides
  6. daohaus

    Finally started my extruded aluminum drawer system.

    A little update as I mustered up some motivation to do some more work on these drawers. I took @LJE design and used wood boards to give the frame something level to sit on. Had a long piece of aluminum angle that I cut down and tied it to frame and will bolt it to the wood planks using the T...
  7. daohaus

    Finally started my extruded aluminum drawer system.

    That's some stout drawer sliders there. Looks like a mix of 10 series and 1020 series extrustions. Nice and overbuilt! I'm trying to figure out right now how to mount it to the back of the truck. I'm afraid to look at what 3/8 aluminum bars cost nowadays so I may resort to wood instead.
  8. daohaus

    Finally started my extruded aluminum drawer system.

    Oh i agree there’s a lot of ways to go about building this and the connecting hardware costs more than the extrusions lol Oh that’s actually a good idea about removing the bottom bar. I like the idea of the reverse ramp to keep things from getting hung up on the horizontal bar. Another build...
  9. daohaus

    Finally started my extruded aluminum drawer system.

    was thinking of corner/L brackets but didnt want to have it interfere w/ the drawer face
  10. daohaus

    Finally started my extruded aluminum drawer system.

    I really love working with extruded aluminum. Bought all my stuff from tnutz.com, their prices are reasonable compared to 80/20 and delivery time frame isnt long (a little over a week). I used inside corner mounts for the middle uprights but thinking of changing that up and buying the drill...
  11. daohaus

    2003 100 HDJ rear fog lights not working….

    I've seen listings on ebay for these, but wasnt sure how bright they are. Also where would the factory rear fog light switch reside?
  12. daohaus

    LX470 Front breaks, wheel bearings service

    Should’ve done this when i did my brake pads today
  13. daohaus

    LX470 2004 | Need help with Android Screen

    Has anyone noticed your car on Apple Maps or Google Maps that the avatar for your car flips around and basically goes haywire when you're sitting still at a light? Only after I start moving does it get its bearing right and not wig out. I had to switch from using Apple Maps because it was...
  14. daohaus

    What have you done to your 100 Series this week?

    Noticed my brake fluid was getting low (down the MIN line) and figured it was time to change the pads. Good thing I did because I had just under 5mm of pad material left when a new set of pads have somewhere between 12-17mm of pad material (per google). I dont know why I psych myself up so...
  15. daohaus

    Lumberjack Engineering: Exquisitely Engineered solutions for the 100 Series Platform.

    Hats off to Alex at Lumberjack. I lost one of my front center cap, sent him one of the original center caps and he generated a new cap that was tall enough to clear the hub flanges. Also ordered the overhead 8 gang auxbeam panel mount and that print fit like a glove. Thank you for the quick...
Back
Top Bottom