Crazy story. Link to the article here.
https://www.carscoops.com/2018/03/new-lexus-lx-470-stolen-2001-now-sold-140k-1k-miles/#ampshare=https://www.carscoops.com/2018/03/new-lexus-lx-470-stolen-2001-now-sold-140k-1k-miles/
$300
This heater unit was in working condition when removed ~20 years ago, and has been in storage since. Because of various modifications an aftermarket unit was installed, so this system is up for sale. I would like to sell it complete if possible. If it doesn't sell complete, then I might be...
This thread will describe how to install a switch and turn the VSC off on a 100 series that is equipped with VSC. I have performed this on my 01 LX470 with success, there may be differences between the models and years that I'm not aware of. I have found a few threads describing issues with VSC...
This is an Fj40 that I have been building for a while and I just recently got it up and running so that I could start driving it. The drive train uses a 350TBI- downey bell housing-H42(from an FJ60)- toybox-splitcase, it will not go into second gear while moving. If I tried to go from 1st to...
This ARB Sahara hoop is off of a 98' Land Cruiser. It has some rust in areas that are not visible when mounted and is in straight good condition. Looking for $30 puss shipping from UT 84070.
PM if interested.
This front bumper is off of an 01 LX470. It is a UCA46 cladding paint code silver color. The bumper and related parts are in good condition with a few minor scratches. The lights are also good. The wire harness connector on one of the signal sockets is damaged but can easily be swapped out...
I have collected an assortment of factory Toyota controls, switches, and blank covers. These are from a variety of models and years. Prices may vary from 10-30$ for the switches and most controls and 2-3for $5 for the blank covers. Buyer pays shipping. Pm me for specific questions or concerns...
These are the lower rear links off of my 01 LX. They should be the same for any 100 series. There are minor scratches in the paint but no dents or bends. The bushings are also in good condition and the bolts are included.
SOLD!
This is a 4 pinion front carrier out of an 07 100 series. It was replaced with an ARB so there was nothing wrong with it and it has been stored well. It ships in the ARB box, and you can calculate shipping of 18.5 lbs from 84070.
SOLD!
WTB headlight housings with adjusters in good working condition. I am not concerned about the paint color or a little surface rust but I need the adjusters and the plastic clips to be in good condition. Attached are pictures of the style I am looking for. Thanks for looking.
SOLD-These parts are for a 79 FJ40. prices do not include shipping.-SOLD
The fuel sender is new in the box PN# 83320-60051. $40-SOLD
Gauge cluster assembly in good condition with minor cosmetic damage. All the gauges worked last time I checked. It has been stored indoors for several years. The...
Looking for a set of factory wheel locks that will fit a 100 series. They can be off a late model Tundra as long as the fit the factory alloy wheels. Please PM me, and thanks for looking.
I figured I would do a write up thread on my 100 series LX build. I recently acquired this 2001 LX470 in October from a good friend who had started the build off to a good start. I'm picking it up from there and moving on to build this vehicle to fit our needs to facilitate vehicle based...
The other day, I realized that I could remove my ignition key from my 2001 LX470 with the transmission selector in the Drive position. It seems like the key should only be removable with the transmission in park. I heard that this was a somewhat common problem, but I havent found anything...
Here is the link to the You Tube upload of my "Highway to Swell" Overnighter video.
It should also be viewable on mobile devices.
Also, you should be able to view my other videos of the previous Cruise Moab Swell events but I'll post their links here as well.
2013-
2012-...
I am looking for a RH front vent louver panel for a 72 Fj40. It belongs in the attached picture. If you have one that you are willing to sell/ship please PM me. I am located in SLC, UT
New in box Nitro 4.88:1 front and rear ring and pinion gear sets.
Gears only front 8" high pinion reverse cut 4.88 ring and pinion, rear 9.5 ring and pinion. SOLD.
Willing to ship with in the lower 48. you can calculate the shipping of approximately 30# from zip code 84070. Buyer pays shipping...
How close to level do leaf spring need to be? If one end is higher than the other will it cause any problems? how much is acceptable? I would figure that the front fixed end could be a little higher than the rear shackle end but maybe theres something I'm not aware of.
Hello all, My truck is an 88 4runner 22RE 5spd named Jubei
I also have a 85 4runner and a 79Fj40. I wont be able to do this all at once but I will get started and then elaborate as I get time. here are most of the specs I have done all the work on this truck myself and I have built most of my...
What drive line angles are you guys running and how are they working for you? I know this varies a lot from truck to truck but I am curious to see what you guys are getting away with. Most of the articles I have read recommend very low angles and I know people are getting away with a lot more so...