zidaro

dig the laid back b-pillars. Nice triangulation but i agree on the windshield bars. Maybe use a removable bar for less intense days? https://www.tmrcustoms.com/collections/roll-cage-chassis/products/notch-ready-interlocking-id-tube-clamp-round

It really is. Leafs front and back but looks really capable. My biggest question was if the rear was dovetailed, and after getting the Owner's IG handle, I confirmed that it is indeed dovetailed. Owner's IG: @fj40wiley

sick ride

Hello, I'm currently redoing my 1985 4Runner. I bought a motor from 22RE Performance and installed it myself back in 2016. I put the motor, new trans and transfer and rebuilt the axles in the truck. I drove it intermittently till around 2021...

https://forum.ih8mud.com/attachments/intakes-jpg.2558473/ that is a 70 narrow runner intake. no clearance issues

I understand your concern, see our fitment notes on the product page:

my hopes right here! I believe the answer may have complexity😂 There is a Wide runner intake that has issues fitting larger diameter header pipes. I have a 68 F and it runs the wide runners. I will have to shave (dremmel) the intake chambers...

Thanks! We made it home. It was tough sledding at times...

Thank you for your order!!!

order placed 😍 super stoked these are a go

Thank you for your interest in our header for the 2F and 1F engines. There are lots of details related to our development of the header and exhaust products here: FJ40 Mark/Downey Header -...

UPDATES! I have pricing for the header. First, thank you all for your interest in our efforts. Before I go further, remember what @gonzopancho said about labor and materials costs - they are "dynamic", so pricing may change. Also, I am trying...

🤙 exactly why i suggested making a slip fitting parallel to and past the muffler that allows any end user to add the final "oem" side exit location piece (and even rotate and trim it a bit if needed, or re-route as needed for a modded setup...

Correct that I have 31's, was thinking about going bigger after I get my PS installed but maybe not! This exhaust is perfection and I don't want to mess with it. The setup that you have configured fits stock FJ40's and people that modify their...

@65swb45 brings up a good point, and reminded me of what modifications I had to do to a new exhaust that was installed when I initially purchased my 40. In the photo below, you can see how the mechanic had the exhaust run a little more than 45...

dump exhaust behind rear shock 45* down. no tire or spring concerns. or leave it as a slip fitting end att shock for user to finish .......though i read comments above and that is a real concern

Follow-ups to a very old thread. 1. Ed left the ice chest that the Fat Tire was in with me as well. 2. That same day, another customer dropped off a carburetor to be rebuilt. Obviously impressed with the karma, when he returned to pick up his...

was hoping you were maybe running it behind OEM 🤙

No idea. It was in it when I bought it. Being a 305, it’s likely an 11”.

what clutch/flywheel you running with it?

For sale. GM SM 465 mated to 1972 3 spd t case. Pulling for 5 spd swap. Runs drives shifts. Includes bell housing. $900 obo. Not sure what a fair price is. Denver.

I have a new in the box Marlin Tacobox that should fit any 4 liter Toyota build but I would do my research before you get too deep into this. It definitely fits the FJ and 4Runners of similar years and engine/tranny specs. This unit was built by...

Nitro changed hands a few years ago and it seems popular opinion is their quality has severely dropped off. They used to be my go to gear mfg. Yukon has a strong warranty and their setup kits are solid. It is the brand i have in my crawler...

New 4X series headlight floor dimmer boots have finally been reproduced! $35 . Made of a tough rubber to stand the test of time and protect the switch contact posts. HERE

1. That is a stock length shackle. You should NOT run a stock shackle with a lift spring; the extra arch of a lift spring requires a wider range of motion than a stock shackle can provide. 2. The offset of the rear spring hanger creates a fulcrum...