Yet another CDL switch question

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 9, 2006
Threads
169
Messages
4,455
Location
Dayton, OH
Hello to all of 80 land,

Well this morning I installed a CDL switch (thanks to a 97 RAV4). I have read almost every thread I can find on this topic and am still a bit confused.

So the switch went in just fine, however did not perform the 7 pin mod as of yet. I fired up the truck and tested the newly installed switch. Put the truck in 4-L and and the CDL and ABS light came on automatically. I then shifted back to 4-H and activated the CDL switch and the CDL and ABS light fired up, activating the CDL. Everything seems fine.....

So is the 7 pin mod performed in order to de-activate the CDL when in 4-L? I guess I am just in need of clarification.

Sorry to repeat such a commonly discussed topic. And thanks for the input.
 
Yes. And also lock the CD when not in low range.

Think of the L lever performing two functions. Changes the transmission shift points and locks the CDL. With the CDL and 7-pin mod you make the lever only perform one function and the switch the other.

HTH
 
Yes that helps a great deal. I figured I was on the right track, but just needed clarification.
 
Yes. And also lock the CD when not in low range.

:rolleyes:

Pin 7 allows the CDL to unlock in Low, that's all it does.

The SWITCH locks the CDL in High. That's the whole point of the switch.
 
After the Pin 7 mod is done, the centre diff will not automatically lock when you shift to low range.

The centre diff lock switch allows you to manually lock the centre diff whenever you want.

Don't do do the Pin 7 mod without having the switch, or you will not be able to lock the centre diff at all.
 
The Pin 7 mod also corrects the shift points in Low.
 
Here's one of the definitive CDL posts from RavenTai:

On a stock FZJ80 there is no CDL switch, the CDL locks up when the T-case is shifted into low.


There is a switch on the T-case near where the shifter goes in, after the shifter has moved from the high range gears to the low range gears this switch sends a signal to a relay, the relay see's this and powers the CDL to lock, that signal comes into the relay on a blue and black wire to pin number 7 hence the name of the mod, the only way to unlock the CDL is to go back to high range so stock you have two options,

High, CDL unlocked
Low, CDL locked

When you add the CDL switch you can then hit the switch to lock the CDL at any time, so you can lock the CDL wile in high range, so now you have three options


High CDL open
High CDL locked
Low CDL locked

But you still do not have the fourth because not matter what the switch position when you shift into low the signal travels down pin 7 and the CDl will be locked,

If you remove the pin 7 signal than that that relay will never see the T-case go into low so it will never automatically lock the center, now with the CDL switch and pin 7 mod the only way that the center ca be locked is via the CDL switch so you have 4 options and complete control of CDL operation.

High CDL open
High CDL locked
Low CDL locked
Low CDL open

T-case gear range and CDL operation are now completely separate and under your control instead of tied. I see why Toyota did it this way, would be hard for the average person who is used to only cars to get their head around a low range much less throwing the mysterious center differential thing in so they took it out of the drivers hands and made it automatic.


If you did the pin 7 mod before getting a switch then you could not lock the center, you would have two options

High, CDL open
Low, CDL open

If you have front and rear lockers you would not be able to lock those either as they require the center to be locked.

Personally I like the real CDL switch even if pricey if only because it has the backlit CDl symbol on it that matches the light, having two hazard switches seams improper to me.
 
The SWITCH locks the CDL in High. That's the whole point of the switch.

Not at all the "whole point".

I discovered and announced this modification and I went after it SPECIFICALLY so that I could operate the vehicle in low range without having the center locked.
 
Dan, refresh my memory... what did you gain by having the ability to be in 4 low, yet without the CDL engaged?

Maybe what'd help me is if you had any driving conditions or types of tasks that you'd use the different scenarios to help put it in context.

Thanks!!
 
what did you gain by having the ability to be in 4 low, yet without the CDL engaged?

To be in low range and able to make tight turns without binding up the driveline is a beautiful thing.
 
Maybe what'd help me is if you had any driving conditions or types of tasks that you'd use the different scenarios to help put it in context.

Maneuvering a boat and trailer into or out of a steep boat ramp.... but there are dozens of similar examples.

-B-
 
I thought I read this somewhere before, but now I can't find it. Does it matter if you are in high or low at the time you add the CDL switch or do the pin 7 mod?
 
One thing that has been bugging me is does it matter if you shift into lo then engage the cdl switch vs engaging the cdl switch and then shifting into lo?

does it even matter?
Just curious.
 
Somethign that came to my mind.
Did anybody ever broke torsen while in LOW, crawling, and with CDL unlocked?
I have to admit I like not locking CDL in low but I had been doing that only on winter runs when there is much less load on transfer case. I am afraid to run unlocked in LOW over the rocks.
 
There is no "torsen" in an 80 Series transfer case.


There is a differential much like a conventional 4 pinion differential in an axle. I have not seen or heard of one breaking.
 
There is no "torsen" in an 80 Series transfer case.


There is a differential much like a conventional 4 pinion differential in an axle. I have not seen or heard of one breaking.

IIRC it's the VC, Viscous Coupler, (not Viet Cong) that can fail to work when over heated in the '93 - '97 vintage CDLs (AKA transfer cases). I believe there is a thread showing how to remove the VC.
 
There is no "torsen" in an 80 Series transfer case.


There is a differential much like a conventional 4 pinion differential in an axle. I have not seen or heard of one breaking.
Now I am confused, so is that means transfer case uses clutch packs... ?
I mean it can not be just plain open-open since it swings rear end when you accelerate.
 
IIRC it's the VC, Viscous Coupler, (not Viet Cong) that can fail to work when over heated in the '93 - '97 vintage CDLs (AKA transfer cases). I believe there is a thread showing how to remove the VC.

The VC can sieze but the failure is not related to operating in low un-locked. It is more related to mis-matched tire sizes.
 
Now I am confused, so is that means transfer case uses clutch packs... ?
I mean it can not be just plain open-open since it swings rear end when you accelerate.

Not clutch packs. It has a 4 pinion differential in it.
 
Not clutch packs. It has a 4 pinion differential in it.
Ok I did go through FSM on this one. I see what you mean by 4 pinion differential, but in HF2AV I see something that looks clutch pack near the output shaft in addition to 4 pinion. Any good explanation how that works since FSM was not clear on it?
I found thread that somebody had actually removed the VC.
I would like to understand how it works. In FSm I dont se how actually that does provide limited slipp to the rear shaft. Thanks in advance for explanation
:cheers:
 
Back
Top Bottom