Wits end

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 23, 2018
Threads
37
Messages
272
Location
Whispering Ranch Az and SoCal
I had my stock carburetor ('67) rebuilt. Ran perfect for about four months but of late it does some very odd things. Come to a stop sign, the idle gets rough or the poor dear starts running very rough like someone poured a cup of gasoline down the throat of the carb and it dies. So there I am at a stop light, stuck. After cranking on it for about twenty seconds it hesitantly fires up runs lousy for about 15 seconds then smooths out so I can limp home. Subject is a '67 one barrel stock 40. It has a solenoid on the carb that clicks when the ignition is turned on. I wish it wasn't there so as to remove another thing driving my mad.
Most of the time the darn thing runs perfect. I've resisted pulling out my .38 to scare the carb into running right all the time. I cannot stand a non reliable vehicle as it vaporizes the fun factor of driving.
Any tips?
 
I changed the fuel filter 75 miles ago. Also had the tank out, cleaned and reinstalled. The window on the carb stays full when running. Will check tomorrow to see where the level is over night. Also I have a one barrel N.O.S carb I can try. I am hoping to use the carb I had rebuilt as it is the one that came on the vehicle (date correct).
As for the new filter, anything is possible, it could be clogged. Certainly easy enough to change out. I also installed a new fuel pump the same time I changed the fuel filter. This was a vehicle that had been ignored for a long time until I bought it two years ago.
 
The next time it dies on you is the time you want to check your fuel window...
Those fuel cut-off solenoids are traditionally very easy to disable, if it's anything like my '74.
Maybe put your other carb on it for a week or so and see if the problem persists, rule out your carb as the problem if it does.
Remember, 50% of carb problems are really electrical.
 
Last summer you had a manifold vacuum leak. You temporarily sealed it, could it possibly be leaking again?

Also last summer your PCV was stuck, have you checked it lately?
 
Maybe the carb fuel bowl float isn't adjusted to spec? Could either be filling the carb with either too much or too little fuel??
 
O.K lads, all good tips, I'm on it. It helps to read others insight as when one is too close to the issue, it tends to cloud the thinking thru being frustrated and pissed. Funny thing is, after fixing the exhaust from the PO (gawd what a cluster that was) I had forgotten about the stalling, but was quickly reminded last weekend.
All the best,
Scoutingranch
 
I had my stock carburetor ('67) rebuilt. Ran perfect for about four months but of late it does some very odd things. Come to a stop sign, the idle gets rough or the poor dear starts running very rough like someone poured a cup of gasoline down the throat of the carb and it dies. So there I am at a stop light, stuck. After cranking on it for about twenty seconds it hesitantly fires up runs lousy for about 15 seconds then smooths out so I can limp home. Subject is a '67 one barrel stock 40. It has a solenoid on the carb that clicks when the ignition is turned on. I wish it wasn't there so as to remove another thing driving my mad.
Most of the time the darn thing runs perfect. I've resisted pulling out my .38 to scare the carb into running right all the time. I cannot stand a non reliable vehicle as it vaporizes the fun factor of driving.
Any tips?
"someone poured a cup of gasoline down the throat" Sounds like flooding. do you smell gas? If so check for a leaky float.
 
If so check for a leaky float.
I thunk about that, wondering if he's got the brass float or the newfangled plasticy type of float. If it's the brass float that's leaky, then it'd stay heavy and be running rich all the time. I was thinking maybe a tiny bit of crap in the needle valve preventing full closure occasionally. Why I was hoping for an observation of the fuel window just after it died, or maybe a description of the great clouds of black smoke out the exhaust as it restarted...
 
I thunk about that, wondering if he's got the brass float or the newfangled plasticy type of float. If it's the brass float that's leaky, then it'd stay heavy and be running rich all the time. I was thinking maybe a tiny bit of crap in the needle valve preventing full closure occasionally. Why I was hoping for an observation of the fuel window just after it died, or maybe a description of the great clouds of black smoke out the exhaust as it restarted...
Even the foam type floats can absorb fuel and weight if the surface finish is cracked.
 
Back
Top Bottom