will this work for me?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 14, 2018
Threads
18
Messages
179
Location
Rochester, NY
Website
aboderoc.com
I just joined this forum. What an amazing resource. I’ve found good info on what to look for when buying and what to expect for maintenance but I have some specific questions about if these vehicles can meet my demands.
In short, I am being persuaded to replace my perfectly good gen 1 Tacoma with something with an automatic transmission. Maybe I have expensive tastes or I’m just an a-hole, either way I need to know if I am making a well informed decision.

Disclaimer: I live in upstate New York and where Its possibly one of the worst places to drive a vehicle that you even remotely care about or want to have last. Or as I call it “where cars go to die”. I refuse to buy a rot box and I don’t want to create one either. I have a thing for vintage vehicles so there is a bit of a conflict of interest there. That brings up my first question; do I have any chance of preserving an older model vehicle with proper undercoating and regular washings, assuming it’s not a daily driver? It will get subjected to road salt since that’s half the year here.

I find the 80 series models to be the most attractive and also within my budget, which is around $10k at the moment. Can I expect to find a reliable LC that doesn’t need constant maintenance or a frame off restoration in order to hand the keys to the sugar mama to pick up some organic carrots from the Whole Foods and expect it to make it back most of the time? I understand the relationship with maintenance and dependability. Assuming I don’t get sold a pig with lipstick, is this a reasonable ask for any vehicle over 20yrs old?

I understand the mileage is fairly horrific and they are underpowered. I’m coming from a 4cylinder supercharged Tacoma TRD, so between the 150hp and a few pounds of boost, I’m not expecting BroDozer circle-jerk power. What I do need is to tow a 3000lb enclosed trailer on a highway for a few hours on occasion. Preferably keeping up with traffic or tackling a modest hill without blowing a rod. I am accustomed to winding out my little 3rz but I have a feeling I won’t be expecting the same drivability with one of these tanks. Do I need to look at the v8 models?

I’m sorry and I’m probably going to catch some crap for this- these are clearly very popular for some reason- which I can only assume that the stock air intake is below the bottom of the axles because what is it with the snorkels? I know the benefits and the cool factor, but it’s the biggest hang up with the lady friend, and unnecessary for our needs yet so many of the rigs in my consideration are getting knocked out of the running for this reason. Taking them back to stock seems like it would require a new fender at least.

I’m still a bit fuzzy on the drive system. I’ve never seen so many configurations of 4x4. In all the trucks I’ve driven, I’m either in four wheel drive or not. I’m comfortable with that. This “center locker” has me all screwed up and full time four wheel drive seems unnecessary and problematic. Do you all drive these for 400,000miles in 4x4? That seems insane.

Options like heated seats and moon roofs, are those fairly common and do the seat heaters work after 20 years? Do to 80 series have rear a/c and associated problems?



I’m really stoked on these things, I hope i can make this work.
 
welcome..... theres a serious shop here in ma. whites gargage and they will lift body and spray everything and not with that sticky oil but for real or you can apply fluid film yourself. I made it thru an entire winter her with a rust free truck and drove it everyday and whenever I could touch up I did but I powerwashed off the salt a LOT. yes they sure do drive them in all wheel, lots of folks have swapped in a set of part time hubs and tweaked the TC. I dont do heated seats so I cant help there.
 
Anything you buy should get yearly treatments with Fluid Film. I spray mine every October before the snow flies.
IMO, an 80 Series is not the correct vehicle for towing. I would be looking for something with a larger engine like the 100 Series or 200 Series, but that's going to be out of your budget.
 
welcome..... theres a serious shop here in ma. whites gargage...
whites automotive in Framingham? I'll actually be in MA next week, right near there.

Anything you buy should get yearly treatments with Fluid Film. I spray mine every October before the snow flies.
IMO, an 80 Series is not the correct vehicle for towing. I would be looking for something with a larger engine like the 100 Series or 200 Series, but that's going to be out of your budget.
I was afraid this would be the biggest problem with the 80 series. It seems like the 4runner platform might need to be considered more seriously for me then as well . The 2000s era had the 4 liter engine which seems to me adequate for the demands .
 
I just joined this forum. What an amazing resource. I’ve found good info on what to look for when buying and what to expect for maintenance but I have some specific questions about if these vehicles can meet my demands.
In short, I am being persuaded to replace my perfectly good gen 1 Tacoma with something with an automatic transmission. Maybe I have expensive tastes or I’m just an a-hole, either way I need to know if I am making a well informed decision.

Disclaimer: I live in upstate New York and where Its possibly one of the worst places to drive a vehicle that you even remotely care about or want to have last. Or as I call it “where cars go to die”. I refuse to buy a rot box and I don’t want to create one either. I have a thing for vintage vehicles so there is a bit of a conflict of interest there. That brings up my first question; do I have any chance of preserving an older model vehicle with proper undercoating and regular washings, assuming it’s not a daily driver? It will get subjected to road salt since that’s half the year here.

I find the 80 series models to be the most attractive and also within my budget, which is around $10k at the moment. Can I expect to find a reliable LC that doesn’t need constant maintenance or a frame off restoration in order to hand the keys to the sugar mama to pick up some organic carrots from the Whole Foods and expect it to make it back most of the time? I understand the relationship with maintenance and dependability. Assuming I don’t get sold a pig with lipstick, is this a reasonable ask for any vehicle over 20yrs old?

I understand the mileage is fairly horrific and they are underpowered. I’m coming from a 4cylinder supercharged Tacoma TRD, so between the 150hp and a few pounds of boost, I’m not expecting BroDozer circle-jerk power. What I do need is to tow a 3000lb enclosed trailer on a highway for a few hours on occasion. Preferably keeping up with traffic or tackling a modest hill without blowing a rod. I am accustomed to winding out my little 3rz but I have a feeling I won’t be expecting the same drivability with one of these tanks. Do I need to look at the v8 models?

I’m sorry and I’m probably going to catch some crap for this- these are clearly very popular for some reason- which I can only assume that the stock air intake is below the bottom of the axles because what is it with the snorkels? I know the benefits and the cool factor, but it’s the biggest hang up with the lady friend, and unnecessary for our needs yet so many of the rigs in my consideration are getting knocked out of the running for this reason. Taking them back to stock seems like it would require a new fender at least.

I’m still a bit fuzzy on the drive system. I’ve never seen so many configurations of 4x4. In all the trucks I’ve driven, I’m either in four wheel drive or not. I’m comfortable with that. This “center locker” has me all screwed up and full time four wheel drive seems unnecessary and problematic. Do you all drive these for 400,000miles in 4x4? That seems insane.

Options like heated seats and moon roofs, are those fairly common and do the seat heaters work after 20 years? Do to 80 series have rear a/c and associated problems?



I’m really stoked on these things, I hope i can make this work.
I wasn in a similar position as yours some years ago. How often to you is on occasion? Because if it is not often at all, then the reliability trumps the towing power. But of course this is opinion. Will it get her there and back with those carrots? Yes sir. At least more so than other vehicles in this age bracket.
 
We own a small vintage furniture store and I do most of the pickups of the pieces we find, as well as some deliveries. I’ll say on average I’m hooking up the trailer once a week and towing it around locally. I would like to be able to tow it within a couple of hours when we hit up flea markets and whatnot in the summers. I do have a F250 work truck if I really need to haul stuff, but it’s a company truck so I try not to do too much personal running around with it.
 
th
whites automotive in Framingham? I'll actually be in MA next week, right near there.


I was afraid this would be the biggest problem with the 80 series. It seems like the 4runner platform might need to be considered more seriously for me then as well . The 2000s era had the 4 liter engine which seems to me adequate for the demands .


Looki here

the 80 is not for you its not a budget rig its 20 year old rig that needs deep pockets

the stock air intake is below the bottom of the axle - Nope its not

the central differential look will give you an headache LOL the 80 is a constant 4X4 rig

and you didnt mention that you need it for what it was born to do - trails and overlanding
 
No. I will not be using it for overlanding. I’m in the wrong part of the country for that activity. It’s a luxury vehicle that has a legendary history and a cult following as well as really impressive safety ratings. So like 99% of the LC’s here in the US, it would be a grocery getter.
The air intake was a joke. Sorry if that didn’t come across.
 
The best way you can think of the driveline is that it's 4WD like your Tacoma, but with a differential between your front and rear axles. Like the differential in your axles that allow your left and right wheels to spin at different speeds when rounding a turn, the center diff of an 80 allows the front and rear axles to spin at different speeds when turning. And just like the diff in your axles, it will allow the axle with less traction to spin while the one with more traction just sits there and looks stupid. Once you lock the center diff, both axles will be turned at the same rate, regardless of which one has traction or not. At this point, it's 4WD the way your Tacoma is 4WD. However... this does NOT lock the diffs in your axles. For that, there's a switch to the left of the steering column on the dash if the truck was one of the lucky 7-10% sold to get them.

To be certain if the truck you're looking at has axle lockers, look at the front drivers door sticker... at the bottom of it, there should be a "K295" if the truck came with factory lockers. Confirm this by looking at the axles themselves; the rear locker mechanism will be on the front side of the axle housing to the drivers side of the pinion, and the front locker mechanism will be on the rear of the axle housing to the passenger side of the pinion. It's very obvious if it's there or not- it looks just like a TRD elocker for a Taco/4Runner, if you've ever seen one of those. Do not just assume the truck has lockers if the switch is present, though... I've caught a few local sellers that said their rigs had lockers but the fuse was blown, when in reality all they did was buy the $45 switch and stick it in the dash.
 
The best way you can think of the driveline is that it's 4WD like your Tacoma, but with a differential between your front and rear axles. Like the differential in your axles that allow your left and right wheels to spin at different speeds when rounding a turn, the center diff of an 80 allows the front and rear axles to spin at different speeds when turning. And just like the diff in your axles, it will allow the axle with less traction to spin while the one with more traction just sits there and looks stupid. Once you lock the center diff, both axles will be turned at the same rate, regardless of which one has traction or not. At this point, it's 4WD the way your Tacoma is 4WD. However... this does NOT lock the diffs in your axles. For that, there's a switch to the left of the steering column on the dash if the truck was one of the lucky 7-10% sold to get them.

To be certain if the truck you're looking at has axle lockers, look at the front drivers door sticker... at the bottom of it, there should be a "K295" if the truck came with factory lockers. Confirm this by looking at the axles themselves; the rear locker mechanism will be on the front side of the axle housing to the drivers side of the pinion, and the front locker mechanism will be on the rear of the axle housing to the passenger side of the pinion. It's very obvious if it's there or not- it looks just like a TRD elocker for a Taco/4Runner, if you've ever seen one of those. Do not just assume the truck has lockers if the switch is present, though... I've caught a few local sellers that said their rigs had lockers but the fuse was blown, when in reality all they did was buy the $45 switch and stick it in the dash.

Correction:

NOT K295.
K294=F/R differential locker
K292=F/R Open Differentials
 
Well said! That makes sense to me. And the "viscous coupler" as I've seen it referred to, is something like a torque converter I'm guessing. I got a good look at a locking differential about a month ago when I swapped them in my rear axle. Here's the actuator motor I pulled out of it:
1482379-6ef7fc212fc9b9209acc505b0d65bf3f.jpg


The best way you can think of the driveline is that it's 4WD like your Tacoma, but with a differential between your front and rear axles. Like the differential in your axles that allow your left and right wheels to spin at different speeds when rounding a turn, the center diff of an 80 allows the front and rear axles to spin at different speeds when turning. And just like the diff in your axles, it will allow the axle with less traction to spin while the one with more traction just sits there and looks stupid. Once you lock the center diff, both axles will be turned at the same rate, regardless of which one has traction or not. At this point, it's 4WD the way your Tacoma is 4WD. However... this does NOT lock the diffs in your axles. For that, there's a switch to the left of the steering column on the dash if the truck was one of the lucky 7-10% sold to get them.

To be certain if the truck you're looking at has axle lockers, look at the front drivers door sticker... at the bottom of it, there should be a "K295" if the truck came with factory lockers. Confirm this by looking at the axles themselves; the rear locker mechanism will be on the front side of the axle housing to the drivers side of the pinion, and the front locker mechanism will be on the rear of the axle housing to the passenger side of the pinion. It's very obvious if it's there or not- it looks just like a TRD elocker for a Taco/4Runner, if you've ever seen one of those. Do not just assume the truck has lockers if the switch is present, though... I've caught a few local sellers that said their rigs had lockers but the fuse was blown, when in reality all they did was buy the $45 switch and stick it in the dash.

MVIMG_20180226_101747_preview.webp
 
whites automotive in Framingham? I'll actually be in MA next week, right near there.


I was afraid this would be the biggest problem with the 80 series. It seems like the 4runner platform might need to be considered more seriously for me then as well . The 2000s era had the 4 liter engine which seems to me adequate for the demands .
hes on rt 9 does a lot of land rovers but always has some sweet LCs in there, he loves the sport and they are good guys.
 
Like I've said before, you have to have deep pockets -OR- normal pockets and solid mechanical skills to own an 80. The parts are still mostly available from Toyota, often at a surprisingly good price if you're a smart shopper.

The full-time 4WD is a great system. The transfer case is all gear-driven, so it lasts (unlike, for example, Jeep's QuadraTrac chain-driven case that's quieter when new but has chain slap by ~100k miles). The part time conversion isn't worth doing unless you have very specific reasons, like front drive like vibes that you can't get rid of.

They're rated to tow 5k pounds, I believe. It won't be like driving a Cummins Ram, but it should get the job done.

$10k should be enough to get you driving a decent one, but only if you're able to do the work yourself. Count on $2k 'baselining' it and replacing all the worn out stuff that the normal PO didn't bother with. The snorkel comment made me think you were looking for a built one (lift, bumpers, tires). If so, you likely won't find a good one in your budget. Shop out west, by the way. Everything I've seen advertised on the east coast is a rust bucket or a fortune.

If towing and comfort are your priority, look at the 100 series. I've seen decent ones around $6500.

Fart warmers: I don't know if they had them in the US (if so, likely on the Lexus LX450). Sunroof: all or nearly all have them in the US. Rear AC: no US models had that feature. Japan and Middle East markets got rear AC and a center console refrigerator. Sugar momma: based on how many break-down posts on 'Mud start with "my wife took the LC to the store", I'm inclined to think that old-timey sailors were right in their superstitious belief that women are bad luck. Best not to risk it.

To be honest, if you're not mechanically inclined, I would suggest a Jeep JK or JL. More expensive, but you don't have to deal with mechanical issues until the warranty runs out. You'll get much better mileage (especially if you get the upcoming diesel) and have insane aftermarket support. Cons: you'll be assumed to be a bro and you'll be driving a Chrysler.
 
EXCUSE ME... Did you just tell me to buy a J**P? Them's fightin' words around here. Haha I'm kidding, but I have talked waaaaay to much smack about Jeeps over the years to actually own one. We vacationed in Kauai, HI this February. I made sure to rent a Wrangler for obvious reasons. It was a total blast, but honestly the 8 Toyota/ Lexus vehicles I/we have owned have been way too good to us to jump ship like that. Half of which were under $2000.

I appreciate your "matter of fact" post. I think I can make the 80 series work if I really want to, but it sounds like a 100 series is much easier to find and in the price range as well. The body lines of the 80 are really what I like the most. The 150 series are nice rigs too. I follow Mud on Instagram and there are some sick looking LS470s you guys rock out.

I am pretty mechanically inclined, so normal maintenance is doable, and armed with knowing a bit about how these things tick seems to go a long way. My BFF (did I just write that?) is a Lexus master mechanic. If there is anything over my head, he's always good for doing me a solid. I have no misconceptions when it comes to planning for and doing the maintenance the PO didn't do. My budget is flexible and does not include selling my current truck or my vehicle maintenance budget.

I would love to find a rig with a lift/ tires/ bumpers, and that's why I was looking on here. There was just an overwhelming number of rigs with snorkels or "scuba" as my lady called it. The trend is migrating over to the Tacoma enthusiasts and it just doesn't do it for me. I ruined a vehicle once from doing a water crossing as a dumb kid. I'm all set with that. My trail riding is typically done on 2 wheels now, but I take solace in having a capable vehicle if the need arises.

I will take your advice about looking out west. I've checked the CL in NC because I know someone out there that could take a look at it for me. I lack any hesitation to do the 'fly and drive' for the right vehicle. It wouldn't be my first time even.

Like I've said before, you have to have deep pockets -OR- normal pockets and solid mechanical skills to own an 80. The parts are still mostly available from Toyota, often at a surprisingly good price if you're a smart shopper.

The full-time 4WD is a great system. The transfer case is all gear-driven, so it lasts (unlike, for example, Jeep's QuadraTrac chain-driven case that's quieter when new but has chain slap by ~100k miles). The part time conversion isn't worth doing unless you have very specific reasons, like front drive like vibes that you can't get rid of.

They're rated to tow 5k pounds, I believe. It won't be like driving a Cummins Ram, but it should get the job done.

$10k should be enough to get you driving a decent one, but only if you're able to do the work yourself. Count on $2k 'baselining' it and replacing all the worn out stuff that the normal PO didn't bother with. The snorkel comment made me think you were looking for a built one (lift, bumpers, tires). If so, you likely won't find a good one in your budget. Shop out west, by the way. Everything I've seen advertised on the east coast is a rust bucket or a fortune.

If towing and comfort are your priority, look at the 100 series. I've seen decent ones around $6500.

Fart warmers: I don't know if they had them in the US (if so, likely on the Lexus LX450). Sunroof: all or nearly all have them in the US. Rear AC: no US models had that feature. Japan and Middle East markets got rear AC and a center console refrigerator. Sugar momma: based on how many break-down posts on 'Mud start with "my wife took the LC to the store", I'm inclined to think that old-timey sailors were right in their superstitious belief that women are bad luck. Best not to risk it.

To be honest, if you're not mechanically inclined, I would suggest a Jeep JK or JL. More expensive, but you don't have to deal with mechanical issues until the warranty runs out. You'll get much better mileage (especially if you get the upcoming diesel) and have insane aftermarket support. Cons: you'll be assumed to be a bro and you'll be driving a Chrysler.
 
The real reason for dorkels is really dust, not water, particularly on gas engines. Getting the intake up high can dramatically reduce the amount of dust picked up by the intake, especially if you're running a convoy in a dusty area. Meanwhile, a snorkle keeps water out, but once it reaches the distributor, you're probably going to be dead in the water. I sometimes watch Australian 4wd videos where they'll spend an entire day driving on dry, washboard dirt roads. It's amazing the amount of dust they knock off their filter elements at the end of a day.

If you look at the parts diagrams for the non-US models, you'll find a genuine Toyota snorkle. So, it's not just bro culture.
 
Oh, and I didn't really tell you to buy a Jeep. I really told you to buy a Chrysler. Real Jeeps were made by Willys or Kaiser. AMC in a pinch. ;)
 
Back
Top Bottom