Waterproofing the Distributor

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 7, 2007
Threads
19
Messages
66
Location
Anchorage, AK
Can someone tell me the best way to prevent water from getting in the distributor? I've seen some pics of cruisers going through water obviously deeper than the distributor.

Inquiring minds want to know. :D

Thanks, Dennis
 
What year are you referring to? What country and what engine? Obviously, diesel 80s will do that all day long....

DougM
 
I just discussed this with a few forum folks (search to find it) but the consensus is that if you use dielectric grease on the distro sealing surfaces and the drain hole it will repel water well enough for deep water usage.
 
The coolest way I've seen is to put an air fitting on the dist cap and run air to it when in deep water. Of course you need on-board air or an air tank.
 
What year are you referring to? What country and what engine? Obviously, diesel 80s will do that all day long....

DougM

OK, me bad. I have a '91 fj80 with a 3fe engine, pretty new to me. I'm in Anchorage, AK, USA.

I don't know how many deep water crossings I will do, but i do know there is no shortage deep puddles and overflow (during winter). Another consideration is for cleaning the engine and engine compartment.

I never thought of using dielectric grease, good idea.

Thanks Much, Dennis
 
For the wire boots I use silicone grease, it excludes water well and makes the wires easy to remove. For the cap and distributor I prefer plumber's puddy, the gray stuff. Just a little bit around the cap base and reinstall the cap, some rolled into little balls and pushed into any holes. It seals well and cleans up easily, without the mess that grease makes inside of the distributor.
 
The coolest way I've seen is to put an air fitting on the dist cap and run air to it when in deep water. Of course you need on-board air or an air tank.

I run this setup and Imho it is the best way. you can run a cheap air compressor and it will be suficiant.. You dont need a lot of pressure
 
The fj60 in my opinion has the best idea for keeping water out of the dist cap. I have put enough moisture with water crossing to mess up my 80 several times, but have never spent the time to mimic my old 60 since I would loosen the top screws on the dist and pry the cap from the body and close the hood and it would convect the moisture out when the truck is hot in about 5 minutes. A couple of years ago i applied the 60 sytem to a old jeep commando and it works great and all the parts are super cheap.

Take a cap and drill and tap two 1/8 npt pipe holes. go to lowes and get two nylon nipples 1/8 male npt by 1/8 hose. go to the help section of any auto part store and by 1/8 plastic vacuum tee and two one way vacuum valves and one of those cheap 1/4 inline fuel filters, and a 1/4 to 1/8 hose adapers plastic, 1 foot of 1/4 vacuum hose and 10 feet of 1/8 vacuum hose. if you get real interested I'll post the help part numbers cut into your vaccum line at that goes to the fuel pressure regulator " up front by the distriburtor and put the tee in the line now make sure you put both one way check valves in series and plumb it to one of the nipples you have installed in the cap. It is extremely important that you make sure it can only suck air out of the dist not let it in from the manifold use two as a safety "Safety the other nippple now is run in to the passenger compartment of the vehicle, and I always installl a cheap 1/4 fule filter one of the clear ones on that end so that dust from insice the vehicle does not make its way into your sit cap As you can see as you run the vehicle you are constanly pulling filtered cabin air through your distributor without having to silcone or whateverever else if you pull from the bottom of the cap you could actually pull any small amount of water that makes it into the cap. I have done enough water crossing to the top of the hood for over 1 minute to assure you your not talking about much water in the cap, just enough without this sytem to spread out and cauxe misfiring not shut down.
 
johnfj, you got any pics of this install? I'm very interested.
 
I do not have any pictures of the jeep and its at hunting camp about 135 miles away. I might get time in the next week or so to buy all the parts and put it on the 80 should have done it a while ago. so if you can wait let me see if I can figure out how to post pictures and take a couple.
 
For puddles in stuff, clean off the distributor and spray your wires and the cap with WD-40.


It's worked so far for me, but for deep water crossings, use other people's advice. Because I drive through puddles. :(
 
Did the job tonight wrote up the material list and some does and donts tried to upload three pictures and lost all of the stuff, so now Im pissed, if sombody can tell me how to attach picture that would be great they have been sized correctly and are in my "attach files"as jpg. it be nice if I could recover everthing I tyed but Im sure its lost. If there is a tutorial somerwhere please direct me.

ktmracer01 if you want me to send the pictures to your private email send me your email in a pm, I can probalby get that done
 
3FE...

Dielectric grease on the distributore Oring. Make sure the Oring is good and the hold down screws are tight. Make sure the vent lines are tight. Dielectric grease under the distributor boots and the spark plug boots (coil wire boot too). Dielectric grease on the coil connections too. Silicon sealant on ay seams in the ECU, ignitor and any/all electrical connections. OEM plug wires fit better than any aftermarket I have come across.

That's about all it takes to water proof the ignition.


Mark...
 
I water proofed my 80 Series like Mark described. It worked great for many water crossings for about 6 years.

Last month I found it's time for round two.:D

BTW, it still ran, rough, but it was running....
water actually "poured" out of the cap when I removed it! Honestly I can't understand how so much water got in. (Well I do know I was acting stupid for an audience.:o)
45run2007+102.jpg


FWIW, never had a problem with my FJ60...yet. Don't forget a SOA and big tires, they help a lot too!
 
The main reason we get water in the 1FZ distro is that the alternator belts run counter clockwise and literally spray water up into the drain hole on the bottom of the distro housing (nice design). If you get into the deep stuff with a bit too much momemtum (as me how I know) you will actually squirt water up into the distro with the force of the water.

Nice huh? FWIW I just greased my distro, drain hole, wires, etc last night.
 
This will not help for a 91 but is another way to do the later models. Link to old thread and a picture since it is now missing in the thread.

Bill
Dist-breather.webp
 
Last edited:
Back
Top Bottom