Transmission pan ST tool

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 24, 2014
Threads
41
Messages
179
Location
Seattle, Washington
Where can I buy the specialty tool for separating the transmission pan from the Transmission?

What type of sealant should I use when I'm ready to reinstall the pan? Will any high temp/oil resistant RTV work as long as it's NOT the clear or blue water pump silcone?

Thanks in advance.
 
The FSM for my 1997 calls for an SST P/N 09032–00100 (Oil Pan Seal Cutter) and FIPG 08826–00090, which I believe has been superceded by 00295-01281 or ThreeBond TB 1281. The general consensus is that Toyota's FIPG is excellent and I'd be hesitant to use anything else.

I personally have not attempted this so I'm unsure if there is an alternate tool. Hope this helps.
 

Attachments

My searches for the SST show that it's produced by OTC. I was under the impression that OTC is the manufacturer/supplier for many Toyota SST's.

Edited for spelling.
 
Last edited:
Correct, at least for the US market. I'm not sure if the OTC-built tools are exported. OTC provides imported and locally manufactured tools for TMS USA.
 
Where can I buy the specialty tool for separating the transmission pan from the Transmission?

What type of sealant should I use when I'm ready to reinstall the pan? Will any high temp/oil resistant RTV work as long as it's NOT the clear or blue water pump silcone?

Thanks in advance.

The pan is nearly 1/16" thick, you could bend the flange if you just got stupid rough with it, but all you need is a good razor knife or thin putty knife. I used a putty knife and hammer to tap into the sealant at several spots along the drivers side of the pan.

Then used a flat blade screwdriver with a taped end to slowly pry down the forward corner (in front of the dipstick tube). After the initial seal is broken, the pan pulls down easily the rest of the way. It isn't the PAN that is the concern really, you don't want to gouge the aluminum mating surface of the transmission.

TransPan1.webp
 
Yup, same as above. Go around it with a putty knife and tap it in with a hammer if you need to. I also used a razor blade first to try to break the seal up a bit. If you're careful and take your time, you should not damage the pan or the block.
 
Where can I buy the specialty tool for separating the transmission pan from the Transmission?

What type of sealant should I use when I'm ready to reinstall the pan? Will any high temp/oil resistant RTV work as long as it's NOT the clear or blue water pump silcone?

Thanks in advance.

Your actual question got answered above, but since nobody else asked...

Why are you taking off the pan?
 
I would do as mention above with putty knife, make sure pan is square on the flange before you reinstall if not it will leak
 
Agree, sst = thin putty knife. Have put a bunch of them on with Permatex Gray, zero leaks. When you have the pan off, turn the system pressure up a notch, makes a nice difference.
 
I bought a paper type gasket instead of using FIPG/RTV when I dropped the pan to change the trans filter (waste of time btw). I sealed everything back up then realized I forgot to put the damn magnets back in the pan. The paper gasket was a lot easier to remove than the FIPG the second time I dropped the pan to put the magnets back in.
 
Correct, at least for the US market. I'm not sure if the OTC-built tools are exported. OTC provides imported and locally manufactured tools for TMS USA.
I sit corrected :)
 
Agree, sst = thin putty knife. Have put a bunch of them on with Permatex Gray, zero leaks. When you have the pan off, turn the system pressure up a notch, makes a nice difference.


^^^^^
Increased mine while I had the pan down installing a temperature sensor. It did make a difference, but nothing dramatic. In my case the shifts (still smooth) just happened a bit quicker. But my tranny has almost 300K on it, so maybe results are more noticeable for others.

LC trans adj1.webp


LC trans adj2.webp
 
Interesting. The transmission was clearly used in several applications/platforms. Does anyone have a definitive list? What platforms used the 'high' setting? What used the 'low' setting?

Found it:
Toyota A transmission - Wikipedia
 
This is one of those SSTs that don't need to exist. Any competent mechanic can remove this pan efficiently with normal tools.
 
i just use a dead blow hammer or rubber mallet, someone at work made an sst out of a chevy or jeep flywheel access cover.

go with the hammer as you probably all ready have one and just dont go crazy beating on the pan.

and red fipg would be the correct fipg from toyota for the trans pan
 
^^^^^
Increased mine while I had the pan down installing a temperature sensor. It did make a difference, but nothing dramatic. In my case the shifts (still smooth) just happened a bit quicker. But my tranny has almost 300K on it, so maybe results are more noticeable for others.

View attachment 1523581

View attachment 1523582

Im honestly curious Turning that dial/knob...what is that for? What does it do?
 
Back
Top Bottom