Transmission Fill

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 2, 2004
Threads
227
Messages
11,510
Location
Washington
What happens if I over fill the transmission? Does it have a way to vent excess fluid? Will it damage anything? If I have added an external cooler will the added volume (.5l) and location have a huge effect on total volume?

Ryan.
 
Is this for your FJ55 or for an 80?

I'm not entirely sure of the answer and rather than give you bad info I'll give you a bump to the top so hopefully you'll get some of the expert's advice
 
As far as I've managed to read from previous posts here, it is not harmful if you overfill your tranny. Excess of fluid will simply go through the vents located somewhere on the dipstick tube or nearby. There is, however, some indirect risk, namely some cars could go on fire if they have the exhaust on the same side as the tranny vents. The oil simply spills on the glowing exhaust tubes and ignites. In the case of the FZJ80, the exhaust is on the opposite side, so there is not a big risk, if any.
 
Hmm. Good info Mike. I will have to take a closer look. I have a V8 so my exhaust routes down both sides. If you add an aftermarket tranny cooler, do most people just overfill knowing that it will run out??? Or do you guess on volume and hope you don't underfill.

Ryan.

As far as I've managed to read from previous posts here, it is not harmful if you overfill your tranny. Excess of fluid will simply go through the vents located somewhere on the dipstick tube or nearby. There is, however, some indirect risk, namely some cars could go on fire if they have the exhaust on the same side as the tranny vents. The oil simply spills on the glowing exhaust tubes and ignites. In the case of the FZJ80, the exhaust is on the opposite side, so there is not a big risk, if any.
 
If you add an aftermarket tranny cooler, do most people just overfill knowing that it will run out??? Or do you guess on volume and hope you don't underfill.

Ryan,

Here are my thoughts...Based on what you stated the after market cooler isn't very large correct? The AT holds a LOT of fluid, so the amount taken up in the cooler should be a fairly small % of the overall amount unless you mounted it way away from the AT and have huge hoses coming off of it.

The stock AT cooler sits up front, ahead of the radiator. I Assume you located your cooler in that general area?

IMO you should just go ahead and fill the AT with fluid to the appropriate level as indicated by the dip stick while cold. Start up the 80 and let it run for say 5-10 seconds. Shut it off and check the fluid level, and for leaks at your new cooler. I would assume the level would go down some as the AT starts sending fluid through the cooler.

Top the level off again and repeat until the fluid level doesn't drop anymore which at that point I'm assuming the new cooler is full and sending fluid back into the AT.

After this, then take the rig for a nice drive and get the AT fluid up to temp and recheck the level and if necessary top it off and call it good :)

I did a complete flush of my AT using the home method of pumping old fluid out and adding fresh in. I had the same worries as you along with the additional worry of pumping too much fluid out at one time. There is no way you can fill the AT up as fast as it will push fluid out unless you have a machine. IIRC I went through 20qts of ATF before nothing but clean fluid finally started coming out.
 
Hmm. Good info Mike. I will have to take a closer look. I have a V8 so my exhaust routes down both sides. If you add an aftermarket tranny cooler, do most people just overfill knowing that it will run out??? Or do you guess on volume and hope you don't underfill.

Ryan.

I don't understand why adding a tranny cooler would require one to over-fill the transmission past the dipstick hash marks. Measurements on most auto transmission dipsticks are made with the engine running, thus the fluid is circulating and not draining backward into the pan as it might if the engine were off. The external heat exchanger might add a quart of total volume to the system's capacity, but as far as measuring the fluid level on the the dipstick, it would be transparent.
 
Back
Top Bottom