Trail Tailor Offerings

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Ordered a pair !

One side will get the damn Antenna off the front bump (hate it there) other will get a nice bright spot to f**k with ANY bastid Kalif tailgaters 'cuz I go too slow! ;) ( I know that ain't nice but do I care?)

Get 'em while they're hot! :eek:

Hey, where's the Kalif plates on Poppy! I'm tellin' !
 
Spike Strip said:
Ordered a pair !

One side will get the damn Antenna off the front bump (hate it there) other will get a nice bright spot to f**k with ANY bastid Kalif tailgaters 'cuz I go too slow! ;) ( I know that ain't nice but do I care?)

Get 'em while they're hot! :eek:

Hey, where's the Kalif plates on Poppy! I'm tellin' !
Click to expand...


Order received! Packaged and ships tomorrow.

We'll see if I'm still here when the registration runs out.... DINGO is good until 11/21 in WY..... HA!

Thanks,

J
 
Feeling a little healthier (physically) so I got started on another round of front "ZERK" bumpers today.

These should go to the coater this week and available late next week for purchase.

Jason


IMG_20190402_142436259.webp
 
I dig those. 60/62 series? If yes, any plans to make a bull bar style bumper?
 
Spook50 said:
I dig those. 60/62 series? If yes, any plans to make a bull bar style bumper?
Click to expand...

These are just the shells. All of these will get a lower profile center bullbar. Last one I did was a higher center bullbar.

J

IMG_20181023_101820722.webp
IMG_20181023_101706782.webp
IMG_20181023_101811062.webp
 
What do the 60 front bumpers run @TRAIL TAILOR ?
 
hey Trail Tailor do you make a high lift clamp / carrier to go on a roof rack? Thanks.
 
TRAIL TAILOR said:
Front is 995.00 powdered plus shipping with center bullbar. 925.00 without bullbar.

Jason
Click to expand...
Do they mount directly to the frame, or to the bumper mounts that are riveted to the frame? Both my bumper mounts are tweaked and I've been wanting to find a bumper that mounts directly to the frame (which is still straight).
 
Spook50 said:
Do they mount directly to the frame, or to the bumper mounts that are riveted to the frame? Both my bumper mounts are tweaked and I've been wanting to find a bumper that mounts directly to the frame (which is still straight).
Click to expand...

Remove the OE bumper brackets and it bolts to the frame. 4 bolts per side.

J
 
TRAIL TAILOR said:
Winch plates are ready to weld into the bumpers.

J

View attachment 1944040View attachment 1944041
Click to expand...
Nice clean welds. Looks like short circuit/hardwire mig? I've found you can get even better penetration by using C25 with electrode positive flux core. Only issue there is you have to clean slag off the weld bead when you're done. It's the process that gets used whenever running wire feed for structural work.
 
Spook50 said:
Nice clean welds. Looks like short circuit/hardwire mig? I've found you can get even better penetration by using C25 with electrode positive flux core. Only issue there is you have to clean slag off the weld bead when you're done. It's the process that gets used whenever running wire feed for structural work.
Click to expand...

I was a CWI (cert weld inspector) for 14 years and FCAW was the #1 weld rejection on RT and MT testing. I'll never run it... It runs hotter but is absolutely a filthy weldment.

I use solid wire ER70s3 and C25 for most of my welding. If not SC I'm pulsing with 90/10 and the same wire.

J
 
ER70s3 is my go-to for solid wire. I wish my welder had enough power to run spray arc honestly. Hot, fast and furious, but I can lay some gorgeous beads with it. Recently I had to go electrode negative flux core to go fix a friend's tractor in central WA. I would've preferred to use 6010 rod on it but I don't have a buzzbox, just my Millermatic. Interesting that FCAW had such high failure rates. We didn't do RT or MT testing for our certifications, all we did was a visual and bend test. My test plates were flawless for that at least, so now I'm curious to see how they would've fared for RT and MT.
 
You must log in or register to reply here.

Share this page

Back
Top Bottom