TJM T17

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

nmesce said:
Just curious, does anybody know how much they weight ? I am considering the TJM T17 or the slee short bus bumper, any thoughts, I know the short bus weights about 90 Lb's

My totally unscientific guess is 50-60 lbs. I mounted it by myself.
 
Can't weigh more than 70 by my guess as well. Mounted it by myself but had to get some help fitting the ENGO 9000. Sweet combo im my opinion.
 
Forgot pics

image-224983586.webp



image-159086345.webp



image-2957633582.webp
image-224983586.webp
image-159086345.webp
image-2957633582.webp
 
Last edited:
htony1...looks fantastic!

Any pros and cons?
 
Just mounted my new T13. Very happy. Check my build thread.
 
94SRUNNER said:
htony1...looks fantastic!

Any pros and cons?

Thanks man I really like this bumper very much. I'm not a rock crawler and my off road consists primarily of forested wooded areas & southeastern swamps where I frequently go alone, hence the winch. The bumper seems to be pretty tough but the instructs could use some updating. I wish they would make a rear bumper in the spirit of the T17. All in all it's a good deal in my opinion for someone who can't drop 2k in an ABR & warn setup.

Pros
You can mount it alone
Decent balance of toughness / weight
A lot of space to mount the winch (slight trimming of the grill support strut was required to install the solenoid cover)
Price
Aux light mounting holes


Cons
had to be trim about 1/4" from the bottom to give the cable clearance behind the fairlead. Used a cutoff blade and a handheld side grinder.
Mounting instructions
No shackle mounts
Lack of AC dryer protection
3 piece design is kinda annoying when aligning the wings

*note: if your ordering this get the wireless control and install it prior to installing it in the bumper. I want retrofit it and now i have to uninstall it to put the wireless control box in.
 
I really like the way this bumper looks. It's really clean looking. Has anyone smacked anything with theirs? I'm just curious how it would hold up to a rock or a tree. Looks pretty stout.
 
Finally got mine mounted along with the lights I picked up at the same time. Started to do the wiring and ran out of kitchen pass time, so they'll have to wait a bit.

I'm not too happy with how the bolt-on wings turned out. I had them on perfectly but had to remove them to put the gaskets on when I received them since I didn't get them originally. When I put them back on I rushed it and they'll need to be redone.

I'm really happy with how it turned out. More aggressive than stock without looking like I'm going to be breaking trail in the Amazon. It bolts on the same way the larger bars do...in fact, they use the same mounts...so I would imagine they'd hold up just as well in an impact.

Before:

http://i126.photobucket.com/albums/p92/timrmoore/cruiser/2012-04-13_08-17-59_544.jpg

http://i126.photobucket.com/albums/p92/timrmoore/cruiser/2012-09-07_10-28-28_764.jpg


http://i126.photobucket.com/albums/p92/timrmoore/cruiser/2012-09-09_12-18-57_2.jpg

http://i126.photobucket.com/albums/p92/timrmoore/cruiser/2012-09-09_12-19-05_776.jpg
http://i126.photobucket.com/albums/p92/timrmoore/cruiser/2012-09-09_12-19-15_207.jpg


http://i126.photobucket.com/albums/p92/timrmoore/cruiser/2012-09-09_12-19-24_296.jpg

http://i126.photobucket.com/albums/p92/timrmoore/cruiser/2012-09-09_12-19-54_815.jpg

http://i126.photobucket.com/albums/p92/timrmoore/cruiser/2012-09-09_12-20-03_385.jpg

http://i126.photobucket.com/albums/p92/timrmoore/cruiser/2012-09-09_12-20-11_586.jpg

http://i126.photobucket.com/albums/p92/timrmoore/cruiser/2012-09-09_12-20-21_687.jpg

http://i126.photobucket.com/albums/p92/timrmoore/cruiser/2012-09-09_12-20-28_445.jpg

http://i126.photobucket.com/albums/p92/timrmoore/cruiser/2012-09-09_12-20-43_806.jpg
 
Can someone with a winch mounted in theirs take a close up picture of the access to the clutch. I'm thinking of this bumper for my new superwinch tiger shark 9500. Thanks
 
Did you look at post 43?
 
I did, but I would like a close up picture of the top with a winch. Curious as to how to access the clutch and solenoid.
 
I just mounted my bumper and will see if the winch fits this weekend. My 9500 fit in the ARB but its looking a little tight for the TJM.

It mounts directly to the bumper no additional winch plate for this bumper.
 
Sorry for the delay here are some pics of it mounted. Accessing the clutch happens through the access cutout or reaching under the bumper. Plugging in the control it is a little tight but not that big of a deal.

Buy the wireless control and install BEFORE you put the winch in!!

ForumRunner_20120915_091416.webp



ForumRunner_20120915_091430.webp



ForumRunner_20120915_091430.webp



ForumRunner_20120915_091450.webp



ForumRunner_20120915_091508.webp



ForumRunner_20120915_091527.webp
ForumRunner_20120915_091416.webp
ForumRunner_20120915_091430.webp
ForumRunner_20120915_091450.webp
ForumRunner_20120915_091508.webp
ForumRunner_20120915_091527.webp
 
Joel @ ENGO sent this pic to me after inquiring about the wiring Ford the wireless control. I didn't do this before but wish I had, now I have to drop the winch to install it.

ForumRunner_20120915_092251.webp
ForumRunner_20120915_092251.webp
 
Thanks, those pictures are perfect. If you clock the clutch that would be easy access. I am going to order the bumper this weekend.
 
Back
Top Bottom