Tie Rod upgrade?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 26, 2013
Threads
25
Messages
186
Location
Anchorage Alaska
Along with overheating the truck this weekend....

My tie rod is bent.

Since I damaged the stock rod, for me, its time to upgrade!!

I'm wondering if the taper in the knuckles is the same as Chevy one ton TRE? Or will I have to ream out the knuckles to accept the GM taper? Thinking 1 1/2 inch DOM is in my future.... getting sick of bending links and rods... :rofl:
 
The taper is smaller on FJ80/FZJ80 tie rod ends. The easy way is to get a replacement that uses the same-tapered end. (trail-gear comes to mind right now, although I'm sure there are others)

If you already have GM TRE's and a tapered reamer, go nuts.
 
Think Cotter Pin and Tie Rod. It is made to give to protect other items.
Make it beefier and bust something more expensive.
Wait till you go to remove the ends and find out they are fine thread and you will likely need the blue tipped wrench.
If you want to go new ends as well, Cruiser Outfitters sells whole kit for about $100 and they are proven 555 Brand.

**Keep in mind that One End of Tie Rod is Right Hand Threads the Opposite end is Left Hand Threads
 
Last edited:
Very common that folks here upgrade all the lower parts, to move all the force into the steering shaft on the box, thus twisting the steering shaft out the bottom of the box.
 
Very common that folks here upgrade all the lower parts, to move all the force into the steering shaft on the box, thus twisting the steering shaft out the bottom of the box.

You mean the splines on the sector shaft ARENT supposed to be in a zig-zag pattern? :hmm:
 
(trail-gear comes to mind

My Fail Gear TRE's went tits up in a little over a year and 20k miles of light trail wheeling and street use. Upon disassembly, there was no grease in the joint and it was completely rusted inside. Furthermore, their kit doesn't include a stud to bolt the supplied steering dampener to the triangle plate on the frame, and after many phone calls with them to include talking with the owner (supposedly), begging them to just send me the god damn $12 part that their kit needs to be bolt in as advertised, they refused and made it quite clear that it's not going to happen, ever.

Your money is best spent elsewhere with people who actually care and that provide a better product.
 
Go to the Classifieds on here or @arcteryx for used replacements.
 
I'm also running Slee's tie rod and drag link with Cruiser Outfitters 555 ends they work well and seem to not bend!!
 
Go with Ruffstuff. This is what they have for our rig FJ80 Tie Rod RH (M23x1.5)

I ended up getting the GM 1 ton TRE's and got DOM tube and weld in bung ends. Been working great for 3 years now. You do need to reem taper the smaller TRE hole with their taper bit.

TRE, Standard, TK234
 
Beware that the TRE's are 23mm but the DLE's are 22mm in case you stay with toyota ends.

Three yeas ago I bought Joint Fuji rod ends from Specter and have had no problems running Rubicon several times. I agree with staying away from TG Chinese garbage.

I made my own tie rod from 1.25 X .250 dom and some threaded bungs I bought somewhere on the net. It ended up costing the same as buying one from Slee so I did buy my drag link from Slee. There material is advertised as 1.25 X .219.

Both rods are well scared by contact with rocks and have yet to bend permanently. Nor have I had problems breaking other components because my steering rods are now "too strong".

I have been reading that theory about upgraded steering rods causing other, more catastrophic, expensive failure's on someone's rig ever since I joined Mud. I did not agree with it back then and my three years of experience with stout steering rods,that don't bend so damn easily, tells me their theory is more like speculation. It all boils down to driving.
 
Last edited:
I just ordered the trail gear garbage, haha. Im hard on vehicles so ill have to come back in awhile and let you all know how it goes. $130 shipped isn't bad. I have a stock spare one i probably should have just swapped in after bending my draglink up the the harmonic balancer. This was most likely from a rock hit that started the bend and i finished it off from having the front locker engaged and trying to turn too hard. Bad driving on my behalf.

Im hoping the stock tie rod behind the axle will be my fuse which i have a few spares of. The trails here have random almost unavoidable rocks that front of axle steering components get abuse from.
 
I'm going to go with the 555's from Cruiser Outfitters and new OEM tie rod and DL. Does anyone happen to have the part #s for the bolt and nut that goes in the OEM clamps?
 
The tie rod and drag link/relay rod take a different sized clamp but the nut and bolt are the same.

91619-61250 bolt
94115-41200 nut
 
I'm going to go with the 555's from Cruiser Outfitters and new OEM tie rod and DL. Does anyone happen to have the part #s for the bolt and nut that goes in the OEM clamps?


I second that emotion! oohhh!


1 x TRE69095 - $97.50
2 x TRET23CLAMP (Fits 6x/7x/8x Tie Rod Tube) - $13/each
2 x TRET21CLAMP (Fits 4x/5x Series Tie Rod & 6x/7x/8x Drag Link) - $13/each
 
Back
Top Bottom