Third Brake Light stays on

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Yeah, I think you've got it under control now. Dig out the meter as needed and start checking those ground points, especially any that have spent some time corroding due to water/salt/whatever.

cheers,
george.
 
I did some further experimentation. with the ignition off, no lights on, if I step on the brake pedal the front and rear marker lights, and the dash lights turn on, as if I had my lights turned on.

Spent some more time with a flashlight and an inspection mirror. STILL haven't seen anything that looks like a ground. Is it a wire on a screw to the body?

I'd seen on another thread to "examine" the wire bundle coming from the body to the lift gate. Yep. There is one. Can't see in there, but the bit you can see looks unmelted and not abraded or cut.

I hate wrenching on cars. Cars suck.

I'm not sure if your cruiser has the Toyota trailer wiring adapter in the back. It's in the rear quarter panel and intercepts signals from the two systems that are affected in your symptom description. You should try unplugging it and see if the problem goes away. Oddly enough, a burnt out or defective brake light bulb can cause the types of issues you are seeing, you might check that as well, remove the brake light bulbs and see if the issue with the other lights coming on goes away. I believe this is caused when the bulb is partially shorted either due to improper installation or internal shorting.

The high mount stop light is grounded at ground point BF, at least it was in 1996 on page 74 of the Birfmark EWD. And no, I have no idea what Birfmark is either. There are a lot of 'mudisms' that are used here that newcomers just don't get. The two main brake lights are grounded at point BG.

Ground point BG is located somewhere under the truck it looks like under the spare tire maybe, shown on page 34, it appears to be externally mounted. BF is in the center console area and appears to be in the cabin.

Toyota doesn't just ground everything to the nearest piece of sheet metal, they run ground wires in the harness to the 'harness ground' point for the entire harness. The ground wires snake through each harness to each connector and join in various splices and multiple termination pin terminations. You can test continuity from the negative side of the stop light to the body for a quick check. You should get a very low resistance, and if you probe directly to the related ground point it should be basically 0 ohms.

I'm not convinced that the EWD is universal enough to be trusted to be accurate from year to year.
 
I would be check "Frame Wire 2" on page 34 first. Seeing as how you had some rust on your rig and that area is known to be a problem with moisture. I had a problem with my ground there. A little 800 grit and dielectric grease and no more problemo!

If it's not that at least you narrowed it down and will feel good about it! :)
 
<snip> And no, I have no idea what Birfmark is either. There are a lot of 'mudisms' that are used here that newcomers just don't get. <snip>

FWIW (For what it's worth) (also in the FAQ). Birkmark is an username/alias here. He complied one of the couple PDF versions of the FSM/EWD.
 
FWIW (For what it's worth) (also in the FAQ). Birkmark is an username/alias here. He complied one of the couple PDF versions of the FSM/EWD.

FWIW is fairly standard abbreviation, and yes most of that stuff is in the FAQ. Birfmark isn't in there though, thanks for the explain.
 
I got my rig up on a lift today, and finally found a ground wire. It was under the spare, and obscured by the spare tire crank channel. I cleaned it up, but it didn't fix the problem.
ground.webp


I did find a known issue. This connector under the driver side kick panel will kill the rear left turn signal when wiggled. When it stops raining buckets, I will take it apart and clean it up. I don't know if it will fix the other issue, but I figure fixing this will be good and could possibly lead to more information about the brake light issue.

.
connector.webp
 
I would be check "Frame Wire 2" on page 34 first. Seeing as how you had some rust on your rig and that area is known to be a problem with moisture. I had a problem with my ground there. A little 800 grit and dielectric grease and no more problemo!

If it's not that at least you narrowed it down and will feel good about it! :)

Frame Wire 2 looked good. Cannot find a ground on it, though.
 
I got my rig up on a lift today, and finally found a ground wire. It was under the spare, and obscured by the spare tire crank channel. I cleaned it up, but it didn't fix the problem. View attachment 1202745

I did find a known issue. This connector under the driver side kick panel will kill the rear left turn signal when wiggled. When it stops raining buckets, I will take it apart and clean it up. I don't know if it will fix the other issue, but I figure fixing this will be good and could possibly lead to more information about the brake light issue.

.View attachment 1202744

You see that corrosion where the wires go in to the plug? I think you need to really clean those up. I think you may be on to it.
 
After a lot of cussing and gentle teasing, got this thing pulled apart. It's the main connection going aft of the firewall for just about everything.

Fixed the dash lights coming on when pushing the brake pedal when apart. But of course nothing lit up while it was so. Cleaned it up and reassembled, and...

Didn't fix a damn thing. In fact, it made the left turn signal problem worse. Much more touchy now.. The pulling apart must've tweaked something.
0bb9fda7-ce3e-4490-a7a0-a4f1a2a01d83.webp
 
If you've cleaned the contacts enough that you get electrical connections on each pin and no corrosion is bridging pins, then I doubt it is the culprit.

After looking at the EWD for a while for both the brake and running light/dash light circuits there are really only a few systems that bridge the circuits. First is the trailer harness adapter. Verify if you have one of those, and if so unplug it. Simple test, and if you don't have one it helps to eliminate one potential source of issues.

The next is the ground points. This is a shared ground between tail lights and stop lights. That should be the one under the frame that you already found. The tail lights are grounded here through junction B31. You should unplug one of the tail lights and use a multimeter to check continuity to ground. Test between the White/black wire and clean metal on the body/frame. It should be less than 1/2 an ohm. If not, check splice point B31 (depicted on page 36) and ground point BG (page 34, but you already found this one). The parking lights have their own ground at point EB and EA (page 30, front of rig). Do the parking lights come on when you press the brake pedal or only the dash/tail lights?

Another common point is the brake light bulbs themselves, as well as the sockets they sit in. Somehow power is leaking into the positive side of the power source for the tail/park lights. A bad bulb, corrosion in the bulb holder, or improper seating of the bulb can cause leakage.
 
Yup. Recommend going thru the trailer wiring converter harness, IF you have one. I have found at least 3 different setups so far. One of them does say Toyota on it. One of them uses Scotch clips to hook it up. Most lay on the right rear quarter, but a few are in the left. Mostly accessible thru the tail light hole.
 
If you've cleaned the contacts enough that you get electrical connections on each pin and no corrosion is bridging pins, then I doubt it is the culprit.

As of this time, I am not certain that connection is good. It still causes the left turn signal to malfunction, when you wiggle it.

After looking at the EWD for a while for both the brake and running light/dash light circuits there are really only a few systems that bridge the circuits. First is the trailer harness adapter. Verify if you have one of those, and if so unplug it. Simple test, and if you don't have one it helps to eliminate one potential source of issues.

The next is the ground points. This is a shared ground between tail lights and stop lights. That should be the one under the frame that you already found. The tail lights are grounded here through junction B31. You should unplug one of the tail lights and use a multimeter to check continuity to ground. Test between the White/black wire and clean metal on the body/frame. It should be less than 1/2 an ohm. If not, check splice point B31 (depicted on page 36) and ground point BG (page 34, but you already found this one). The parking lights have their own ground at point EB and EA (page 30, front of rig). Do the parking lights come on when you press the brake pedal or only the dash/tail lights?

Yes, the parking lights definitely come on when brake pedal is depressed. Also, there is a pronounced solenoid clicking sound, when the brakes are depressed, but the lights are not on.

Another common point is the brake light bulbs themselves, as well as the sockets they sit in. Somehow power is leaking into the positive side of the power source for the tail/park lights. A bad bulb, corrosion in the bulb holder, or improper seating of the bulb can cause leakage.

I removed each bulb and it did not correct the issue.
 
Yup. Recommend going thru the trailer wiring converter harness, IF you have one. I have found at least 3 different setups so far. One of them does say Toyota on it. One of them uses Scotch clips to hook it up. Most lay on the right rear quarter, but a few are in the left. Mostly accessible thru the tail light hole.

There are definitely some extra unused connectors in the back. I will sort through them tomorrow, when I have light to work. Thanks!
 
Under your jack is a set of connections as well. Since your roads are salted check this as well.
Unplug and check your other lights, clean and put togethr with dielectric grease.
 
Under your jack is a set of connections as well. Since your roads are salted check this as well.
Unplug and check your other lights, clean and put togethr with dielectric grease.

This tip led me to the first useful data point so far.

There were two connectors back there. One I disconnected, which knocked out the rear lights, but didn't affect the marker lights and dimming when brake pedal was depressed. The other did nothing I could discern.

What makes this significant, imo, is that when I disconnected the front connector, shown below, it took out all the electrics aft of the firewall AND it stopped the marker lights and dash dimming when the brake pedal was depressed.

I would say the issue, then, is somewhere in between those connectors, wouldn't you?

20160204_141353.webp


0bb9fda7-ce3e-4490-a7a0-a4f1a2a01d83.webp
 
For anyone who needs to find the center ground, "BF", it is located under the console, on the stiffening member that runs transverse under the front seats. As you can see from the pics, mine is clean and the chances of it being the issue is nil. It is a common ground for #1 and #2 floor wire, from what I can tell.

20160206_100251 (1).webp


My wiring loom there had a bunch of cobbled together crap; the rear cigarette lighters had been repaired at least once, so I cut all that out of there, just to be sure.

There are several empty female connectors sitting under there, doing nothing I can discern. They looked ok, though, so I left them.
 
Did you ever get look at the headliner to hatch wiring?
If you get there you may find that some wires are touching or grounding
 
Did you ever get look at the headliner to hatch wiring?
If you get there you may find that some wires are touching or grounding

That would be the "Back Door #1 Wire"?

I'm tackling this a little bit at a time, and frankly, as wet as it has been, I think this is probably the lowest potential problem area. Plus the hardest to get to. I pulled the rubber sleeve that goes from the headliner to the hatch, realized it looked fine and I couldn't see sh*t by doing so and just struggled for an hour trying to get it put back in.

I'm going to hit the driver's front kick panel area again. I need to find a way to get in there without standing on my head, and think I am going to cut some zip strips to try to pull the looms out to where I can actually see them.
 
Back
Top Bottom