Tacoma DC joint

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 16, 2014
Threads
51
Messages
772
Location
Union, Ky
One of my front u joints finally blew up last week on my 4" lifted cruiser. I had an idea and was wondering if it's possible/sensible to just use the DC joint off a Tacoma shaft on the stock shaft and just have it shortened. The reason I ask is because I am have zero luck finding a whole shaft anywhere but online and expensive, and the DC joints themselves are on eBay for $30-$40. Any thoughts?
 
I don't see a problem with that.
 
there are a lot of potential problems with what you are wanting to do. First, the toyota drive shafts uses an expanded tube which shouldn't be shortened. So that means you would need to retube. Toyota uses metric sized tubing and sourcing that can be a real challenge.

Next up would be the DC joint you are referring to. I couldn't find them so I can't be sure but would expect that they are spicer joints and as such will require a different size tubing than the Toyota joint does.

So now you'll need to deal with that mismatch size with a sleeve or something which can produce a shaft that will vibrate.

In theory it sounds easy enough but there are difficulties in executing it.
 
I would be very interest to know how Slee makes their DC shafts.
 
there are a lot of potential problems with what you are wanting to do. First, the toyota drive shafts uses an expanded tube which shouldn't be shortened. So that means you would need to retube. Toyota uses metric sized tubing and sourcing that can be a real challenge.

Next up would be the DC joint you are referring to. I couldn't find them so I can't be sure but would expect that they are spicer joints and as such will require a different size tubing than the Toyota joint does.

So now you'll need to deal with that mismatch size with a sleeve or something which can produce a shaft that will vibrate.

In theory it sounds easy enough but there are difficulties in executing it.
I undrstand the shortening problem, however, the way I was imagining the joint was to keep the partof the joint attached the the stock shaft and add the Tacoma joint onto that. Hopefully that makes sense...
 
I undrstand the shortening problem, however, the way I was imagining the joint was to keep the partof the joint attached the the stock shaft and add the Tacoma joint onto that. Hopefully that makes sense...

yes but the DC joint is longer than the stock u-joint so the tube section would need to be shortened. Can you post a like to those ends from EBAY?
 
There is no rocket science in having an high angle drive shaft custom built. Any local decent shop can build you one for a reasonable price. For example, I know that in Vancouver, BC area, a custom DC drive shaft for first or second gen 4Runner will be around 120 CAD to 150 CAD...(High Angle CV Joints - Trust the Professionals at Pat's Driveline for example is a well known shop in Vancouver BC area).
 
There is no rocket science in having an high angle drive shaft custom built. Any local decent shop can build you one for a reasonable price. For example, I know that in Vancouver, BC area, a custom DC drive shaft for first or second gen 4Runner will be around 120 CAD to 150 CAD...(High Angle CV Joints - Trust the Professionals at Pat's Driveline for example is a well known shop in Vancouver BC area).
It's well documented here on Mud where members have used Taco front DC joints to make custom front shafts for 80's. I live only 30 minutes from a very experienced, very good driveline shop and opted to have them build me a front DC shaft with a spider 1310 CV and the Toyota joint at the pinion. This was not cheap but also not uncommon. Don't have a lot of miles on it yet but it has some hard ones like those on the Rubicon and such with no issues yet and I don't expect any either. I am actually considering a DC shaft to address a vibration in the rear that I can't seem to resolve with a shaft rebuild and adjustable Contol arms. The DC joint takes pinion angle out of the equation leaving you set up for variable inches of lift as long as you can adjust your pinion into very close alignment with the driveline itself.
 
There is no rocket science in having an high angle drive shaft custom built. Any local decent shop can build you one for a reasonable price. For example, I know that in Vancouver, BC area, a custom DC drive shaft for first or second gen 4Runner will be around 120 CAD to 150 CAD...(High Angle CV Joints - Trust the Professionals at Pat's Driveline for example is a well known shop in Vancouver BC area).


absolutely true, however that is usually predicated on using spicer joints which in my personal experience and others is a short term solution. I had bought two spicer built shafts and the most mileage I got out of either one was 20k. I then went with a modified Tacoma shaft and have since sold the truck and the new owner is still driving with it, over 100k.

If you daily drive your truck or like myself do long distance runs with it, I would avoid a spicer solution.
 
Not the 1st time Dana/Spicer let Toyota down:

2011-01-18 18:00
Dana Corp ordered to pay Toyota $25m for frame rust issues

Dana Corp of beautiful Maumee, Ohio has been ordered to pay $25 million to Toyota for problems with parts provided by Dana to Toyota which resulted in the 1995-2000 Tacoma pickup frame-rust recall.
Dana is best-known for their rear differentials and axle assemblies but for the 1995-2000 Toyota Tacoma, Dana provided the frame that was found to rust excessively, causing Toyota to issue a recall on 110,000 pickups built during those six model years. This recall affected mostly those who lived in areas with harsh winters and the rust problem was accelerated by the use of road salt.

Toyota was Dana Corp’s second largest customer in 2009, with 6% of their business coming from the Japanese automaker; second only to the 20% of business that Ford Motor Company provides. This $25 million payment will be charged against the earnings of 4th quarter of 2010 and while it sounds like a tremendous amount of money, Dana reported $6.1 billion in revenue during 2010 – meaning that the $25 million fine is likely only a small portion of the money made off of Toyota throughout their relationship.

Dana Corp sold the plants responsible for the faulty Toyota Tacoma frames that were affected by the recall in March 2010 but as part of the settlement between the two over the frame rust recall issue, Dana will shell out the cash as the plants were in their ownership when the problematic parts were produced.

Dana Corp ordered to pay Toyota $25m for frame rust issues - Torque News
 
absolutely true, however that is usually predicated on using spicer joints which in my personal experience and others is a short term solution. I had bought two spicer built shafts and the most mileage I got out of either one was 20k. I then went with a modified Tacoma shaft and have since sold the truck and the new owner is still driving with it, over 100k.

If you daily drive your truck or like myself do long distance runs with it, I would avoid a spicer solution.
I am very interested in the explanation for this from a mechanical/engineering standpoint.
 
I guess it depends where you are, the shop we use has no problem shortening, retubing, etc, Toyota shafts, commonly done for them.
 
in regards to baldilocks comment:
I'm also more than interested and curious to get an educated opinion, mechanical/engineering perspective.
 
absolutely true, however that is usually predicated on using spicer joints which in my personal experience and others is a short term solution. I had bought two spicer built shafts and the most mileage I got out of either one was 20k. I then went with a modified Tacoma shaft and have since sold the truck and the new owner is still driving with it, over 100k.

If you daily drive your truck or like myself do long distance runs with it, I would avoid a spicer solution.
So is Spicer the best alternative to OEM, are basically all aftermarket joints crap for DD? I'm just curious
 
So is Spicer the best alternative to OEM, are basically all aftermarket joints crap for DD? I'm just curious
The Driveline shop in Sacramento that I have used for many years uses Spicer and NeapCo joints only. However, If i were to request a Koyo joint in my Toyota shaft they would install that as they have agreed that Koyo is pretty much the best. The Spicer sealed joints in my Dodge are at 115k with no problems yet.
I think that the problem mentioned here may be when we install a Spicer joint into a Toyota yoke. I recall reading something about this here in the Mud archives.
 
Last edited:
This discussion has caught my attention. I recently had the rear shaft of my 3rd gen 4Runner rebuilt (rear shaft is DC from the factory, similar to the Tacoma) and the shop said he didn't bother rebuilding the DC joints, just cut it off and welded on a Spicer DC. Reading the above has me curious now if I now have a Spicer Joint installed in the Toyota yoke at the T-case end of the shaft, and if so, will I run into issues in a few thousand miles. My original shaft went 270k before it gave up the ghost. I am now thinking that what was done may end up costing me more in the long run than if I had just ordered a new one from Toyota.... especially since I average 30k a year on the road.
 
This discussion has caught my attention. I recently had the rear shaft of my 3rd gen 4Runner rebuilt (rear shaft is DC from the factory, similar to the Tacoma) and the shop said he didn't bother rebuilding the DC joints, just cut it off and welded on a Spicer DC. Reading the above has me curious now if I now have a Spicer Joint installed in the Toyota yoke at the T-case end of the shaft, and if so, will I run into issues in a few thousand miles. My original shaft went 270k before it gave up the ghost. I am now thinking that what was done may end up costing me more in the long run than if I had just ordered a new one from Toyota.... especially since I average 30k a year on the road.
If they put Spicer joints into a Spicer DC/CV joint, there should be no problem. My question is, what joint was used at the pinion end assuming the Toyota yoke was retained?
 
If they put Spicer joints into a Spicer DC/CV joint, there should be no problem. My question is, what joint was used at the pinion end assuming the Toyota yoke was retained?

I am not 100% sure if it is an OEM joint, but from the brief conversation with the guy who did it, I gathered that it was not a Spicer but something to Toyota Spec. I say that because he made specific mention that the DC/CV now had "those Ford and Chevy Joints that are alot easier to get"

My question comes from the CV/DC flange for the T-case. The new one had the flange connection on it and I am not sure if it is a new flange attached to the new DC/CV unit that was installed. Now that I think about it, it has to be a new flange on that end as well because the new joints are retained with the snap rings on top of the caps and the Toyota joints are retained from the inside, so it must have been a complete unit.
 
This discussion has caught my attention. I recently had the rear shaft of my 3rd gen 4Runner rebuilt (rear shaft is DC from the factory, similar to the Tacoma) and the shop said he didn't bother rebuilding the DC joints, just cut it off and welded on a Spicer DC. Reading the above has me curious now if I now have a Spicer Joint installed in the Toyota yoke at the T-case end of the shaft, and if so, will I run into issues in a few thousand miles. My original shaft went 270k before it gave up the ghost. I am now thinking that what was done may end up costing me more in the long run than if I had just ordered a new one from Toyota.... especially since I average 30k a year on the road.
How much did they charge to put on the new dc joint?
 
Back
Top Bottom