Sway bar ripped off -again

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 8, 2006
Threads
24
Messages
195
Location
Chugiak, Alaska
I've decided that the front sway bar is just too restrictive for OME J springs. I ripped the passenger side off the axle last summer which also broke the brake line. I replaced the line and welded the mount on good. On Saturday, I ripped the mount off again on the same twisty trail. This time the base of the mount stayed on the axle and the ears ripped off with the sway bar, breaking the brake line again. I'm going to have to fab up a new mount and make disconnects for the bar. I have the bar extended down 3" already. I'm thinking the bar just can't move enough and something has to give, so the mount breaks.
 
i do notice mine leans more in turns while it's out. I plan on putting mine back in. However, a disconnect type deal would be great. I just don't have the time, fab skills, or equipment to mess with it right now.
 
I haven't had mine on for over 3 years with no real negative impact.

It might not be something you will notice all the time but since I'm not driving a trail dedicated rig I want any advantage on road I can have especially if it doesn't provide any benefit off road.

These trucks lifted have a roll over tendency as it is and throwing away sway bars doesn't seem like a good idea to me.
 
It might not be something you will notice all the time but since I'm not driving a trail dedicated rig I want any advantage on road I can have especially if it doesn't provide any benefit off road.

These trucks lifted have a roll over tendency as it is and throwing away sway bars doesn't seem like a good idea to me.

Point taken. Mine rarely sees any road time and any road time is getting to a trail.

I would not be surprised if my roll-over in 2007 was in some slight part attributed to not having a front sway bar...don't know, probably never will, but worth thinking about.

-o-
 
I haven't had mine on for over 3 years with no real negative impact other than rolling it over during a high speed maneuver and crushing the roof, busting the windshield, and scaring the crap out of my dog; then needing to weld all the doors and sunroof shut but I can still crawl in through the driver window. Don't get many second dates though.

Fixed it for ya.

-B-
 
why would you want to get rid of the sway bar. It's been shown that it doesn't impeded flex and when removed negatively impacts on road handling.


I think it does help flex. By taking the front off, the rear forces the front to move a little better. Are you going to see massive amounts, no. But it does help. Taking both off allowed a decent change in my flex ability. However, I run the rear sway now because of towing and the fact that the rear already flexxes good.

It think running Slee springs helps as well. If it were just "J" or less, It would probably have more bodyroll.
 
Quick disconnects are not that tough guys. I'm using simple spring pins. I had them on all the way out to Moab and re-connected them in the parking lot at the slickrock trailhead.

I used bailing type wire to tie the sway bar up to the frame rails and out of the way while wheeling.

You can also just drop the sway bar all together with 4 bolts off the mounting brackets... then slap it back on when you're ready to go home.
 
I am with the "Ditch the swaybar" crowd.

Mine tore off last summer and took the break line out, way up a very difficult trail.

Took it off when I got home and have not looked back.


Me too. I don't think it make it any harder to control on-road without the swaybars. Even in panic manuvering... And I've been in that situation more than once (damn Oregon drivers...)
 
I just unbolt mine for rock crawling trails and don't worry about it for the drive to and from the trail. This is the not-quick disconnect version. Really not a big deal compared to ripping off a brake hard line on the trail, and then it is on for the off season full time.

I really don't feel a difference with just me, but with family and gear I can tell, and it's worth the effort. 15 minutes on each end. Offroad I think it is absolutely more balanced with front removed and rear installed.
 
I second the QDs for the front. If you leave the rears connected and the front disconnected, the front suspension will open up very nicely.

I see no reason to get rid of it unless this is your trail truck exclusively. For those folks who have no sway bars can compensate with better valved shocks but still, the vehicle handles way differently.
 
Last edited:
I might mention that OEM brake lines aren't always that easy to source. I'm waiting on mine to be shipped from Japan. Luckily mine is not a DD right now. I will definitely look into sway bar disconnect or removal when I am able to get into some more serious trails. FWIW, I removed the sway bar on my 95 chev IFS that had a 6" lift and 35's. I was worried about on road handling at first, but it ended out being fine. It was a little wobbly on hard turns, but I never felt like I was going to roll. Obviously this is different from an 80 in many ways.
 
Back
Top Bottom