swapping birfield

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 21, 2016
Threads
7
Messages
46
Location
red clay Ga
Hello fellow Fj80 owner, I'm new to this forum and this is my first Landcruiser or SAS rig. I recently acquire a fj80 free from a family member . When I receive the truck I was advise that both axle are popping . I have read a lot about the front axle on these solid setup on these Yota . I did read about somebody saying swapping axle from one side to another to see if the noise go away. I'm confident that the noise is a birfield but I'm not a expert on these rigs. I have search the world on answer for this problem on expedition portal ,marlin crawler but nobody really states what the problem actually sound like . When it comes to engine mechanical problem I can solve 99 percent of it ,but I'm stunned on axle and suspension issues.
 
Don't swap the axles from side to side, you will have one hanging out much further than the other. But swapping the Birfield joints could solve the problem IF they haven't been previously swapped for the same reason. The process is relatively simple and is explained in a couple threads here. If you are not wheeling hard or, like mine, if you only hear the noise when you are turning hard and on the gas hard, you prolly have a little time.
 
Likely the drive splines have stripped, in which case you need to replace the birfields.
 
Mine popped when turning, and the splines were absolutely stripped.
 
The Reality:
If your going in you might as well rebuild (unless you know when it was done)
Going to cost you about $200 and 2 days time and a set of clothes.
Buy a box of Nitrile gloves or trim your nails super short.
The Lifelong Skill-set you will learn is free.

I'd order up a kit from Cruiser Outfitters and add as needed.

Front Axle Rebuild - For FAQ

After your done with that I would check the gear oil in the transfer case and rear differential, and replace as needed.
 
Noise descriptions over the interwebs are always subjective but your on the right track asking and searching on this site.

Until you have time to do as Hornd suggests above you could try and see if they are simply dry.... or washed out with gear oil.
There is a square plug on top of the knuckle. Remove it and stick a zip tie or long thin screwdriver in and make sure you get it to the bottom. Remove it and see where the grease line is; it should be 3/4 full of Moly grease. If not, pump a tube of grease in it or enough to fill it up, it will redistribute and lower the level. Not an ultimate fix, and it wont ever get into the bell where you really need it but may provide you a hint to if thats your issue.

IF this is not an issue your comfortable with tackling (though its more messy and time consuming than difficult, however a critical system not to muck up) then give a ring to ACC garage. Depending on how far you are from atlanta, they would be a great option for wrenching or on site diagnosing of the issue. Good luck.
 
Not an ultimate fix, and it wont ever get into the bell where you really need it
Has this been confirmed? When driving with the wheels turned, there should be a significant hydraulic pumping action as the balls roll back and forth in the races. The layout and method of operation is very similar to a hydraulic piston pump.

14273_105_2.jpg
 
ok ill refrain from absolutes... to appease the technicality minded i should have said IMO it wont get as complete coverage as a true hand packing when out of the truck, or even better I dont think it will reach as many places it needs to go as an axle rebuild (between stub shaft and spindle comes to mind, the bushing as well) Plus mines not a circle track vehicle ;)

There has to be a reason folks bothered to R & D the gun drilled birfs. and others take the effort to mod theirs.
 
Very valid points. I was not trying to call you out, just reflecting on the squirting and sucking noise my birfield was making when I moved it with my hands to pack the grease.
 
If the truck was not wheeled hard I would not expect the drive splines to be stripped.

Front end probably just completely neglected like a standard soccer mom SUV.

Check the grease level from the top of the knuckle as stated. Add a tube in each side as it's probably low. That always made my click better for a little while. Report back.

Are the knuckle seals leaking? Gear oil level good in diff?

I put new birfs in this year at 220K. Plenty of hard wheeling on the original Birfs. You can drive a long time on the road with worn birfs if you don't crank the wheel under max load.

If your going in for a rebuild, (Basically the right of passage with 80 series ownership) do the brakes at the same time. Get some OEM rotors from someone like @beno or choose a quality aftermarket part. Don't skimp here. Personally I like DBA rotors and ebc pads. But hard to go wrong with OEM for the price.
 
He has a 92 so it has the shorter/weaker drive splines.

Y'all told me over and over I needed to swap my birfs, and it turns out the splines were shot. OP can check them really easily and same himself from tearing down the axle and having to wait for new birfs to arrive.
 
If the truck was not wheeled hard I would not expect the drive splines to be stripped.

Front end probably just completely neglected like a standard soccer mom SUV.

Check the grease level from the top of the knuckle as stated. Add a tube in each side as it's probably low. That always made my click better for a little while. Report back.

Are the knuckle seals leaking? Gear oil level good in diff?

I put new birfs in this year at 220K. Plenty of hard wheeling on the original Birfs. You can drive a long time on the road with worn birfs if you don't crank the wheel under max load.

If your going in for a rebuild, (Basically the right of passage with 80 series ownership) do the brakes at the same time. Get some OEM rotors from someone like @beno or choose a quality aftermarket part. Don't skimp here. Personally I like DBA rotors and ebc pads. But hard to go wrong with OEM for the price.

I had not idea they were only $70!

TOYOTA OEM Front Brake-Disc Rotor 4351260171
#14 on Diagram Only-Genuine OE Factory Original Item

Be the first to write a review.


Email to friends Share on Facebook - opens in a new window or tab Share on Twitter - opens in a new window or tab Share on Pinterest - opens in a new window or tab
| Add to watch list
Seller information
hoov_toyo (633 )
99.5% Positive feedback
Follow this seller
Visit store:
hoov_toyo
See other items

Item Information
Item condition:
New
Compatibility:
See compatible vehicles
Quantity:
4 available / 9 sold
Price:
US $70.75
Buy It Now


Add to cart
Qualifies for:
1-yr protection from Assurant - $12.491-yr protection from Assurant - $12.49 Opens a information Overlay

5 watching
Add to watch list

Add to collection
Limited quantity remaining
More than 68% sold
Free shipping

Shipping:
FREE Standard Shipping | See details

Item location:
Birmingham, Alabama, United States

Ships to:
United States See exclusions
 
I had not idea they were only $70!

TOYOTA OEM Front Brake-Disc Rotor 4351260171
#14 on Diagram Only-Genuine OE Factory Original Item

Be the first to write a review.


Email to friends Share on Facebook - opens in a new window or tab Share on Twitter - opens in a new window or tab Share on Pinterest - opens in a new window or tab
| Add to watch list
Seller information
hoov_toyo (633 )
99.5% Positive feedback
Follow this seller
Visit store:
hoov_toyo
See other items

Item Information
Item condition:
New
Compatibility:
See compatible vehicles
Quantity:
4 available / 9 sold
Price:
US $70.75
Buy It Now


Add to cart
Qualifies for:
1-yr protection from Assurant - $12.491-yr protection from Assurant - $12.49 Opens a information Overlay

5 watching
Add to watch list

Add to collection
Limited quantity remaining
More than 68% sold
Free shipping

Shipping:
FREE Standard Shipping | See details

Item location:
Birmingham, Alabama, United States

Ships to:
United States See exclusions

Wrong part number. :lol: Awesome.

43512-60090 is the correct part number.

43512-60171 is for 100 series 1998-2007
 
Thanks for clarifying!

I guess the 60090s are even cheaper!

I won't even bring up the Brake pads, and how 100 Series Pads fit on the 80.

eBay item number:
281719819048

TOYOTA\LEXUS 4351260090 GENUINE OEM BRAKE ROTOR

 
Depending on the thickness of the OP's wallet, he could purchase a couple of new retainer clips for the birfs and swap them side for side after repacking? The amount of work needed is the same as new Birfs but depends on the cash available. I often find no sooner do you start on a simple job like this that you find the top and bottom swivels need doing.........and then........and....

regards

Dave
 
I had not idea they were only $70!

Not sure if that "!" denotes sarcasm or enthusiasm? Or the source of your pricing. All I can say is that when I need OEM parts Beno supplies them to me. Because knowledge is good.
 
Not sure if that "!" denotes sarcasm or enthusiasm? Or the source of your pricing. All I can say is that when I need OEM parts Beno supplies them to me. Because knowledge is good.

I was happy he corrected incorrect information. When the wrong rotor arrived, poster would have been :mad:
 
Back
Top Bottom