Supercharger Bypass????

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 15, 2006
Threads
21
Messages
75
Location
Tucson, Arizona
I decided to pull the trigger on a SC from CDan, but after talking with him a few problems arose and I was hoping for feedback.

I drive roughly 10K miles a year in Mexico and Central America in locations where the octane of the gas is questionable, at best. It sounds like poor quality/low octane gas can create problems with forced induction.

I am trying to figure out a way to EASILY disengage the supercharger when travelling south and restore the stock aspiration. It seems that this can be achieved by removing the belt from the pully, but I am still left with restricted airflow through the SC intake. Any thoughts on a "bypass" or a selectable dual intake system.

I do not have any experience with aftermarket TC or SC systems, so I apologize if these questions seem uninformed. (I have read as many posts as I can find, however!) Thanks in advance for any help, and a public thanks to CDan. I was amazed at the amount of time he took with me to discuss the issue.
 
you can remove the belt from the SC, take the throttle body off the back of the SC and put it back on the intake manifold, then you would need to connect the stock intake tube from the air cleaner to the throttle body , put a cover over the SC inlet and outlet connections to keep it clean. the only problem may be the vacuum lines that are now connected to the SC.. I am sure you could make a small connection manifold for the vacuum lines so that you can just turn a few valves and switch back and forth. It will be a few hours work each time but should work.. either that or a LOT of octane booster..
later
Bret
 
What about those bottles of octane booster. Carry bottles of those and pour in when adding the cheap gas
 
What about those bottles of octane booster. Carry bottles of those and pour in when adding the cheap gas

He would need ~40 of those. Granted, it would be the easiest solution.
 
He would need ~40 of those. Granted, it would be the easiest solution.

So buy 2 cases, throw them in the back of the truck and enjoy your supercharger.
 
So buy 2 cases, throw them in the back of the truck and enjoy your supercharger.

It was my understanding that adding octane booster wouldn't do the trick....am I mistaken? I have mixed 100LL aviation fuel with pump fuel in the past, but it isn't very convenient to fill up at airports enroute.
 
It was my understanding that adding octane booster wouldn't do the trick....am I mistaken? I have mixed 100LL aviation fuel with pump fuel in the past, but it isn't very convenient to fill up at airports enroute.

Where does your understanding of this originate from? I'm not saying your wrong just that in the past I have used 104 octane boost for my 66 plymouth due to the compression the HEMI generated and the lack of leaded fuels in todays world and it worked fabulously. Granted that wasn't a SC engine just a mean old big block but IMO it should work fine and as previously stated by Romer would be the easiest solution.

Course the MADMAX switch thing was the shiznit...............lol
 
I have the answer!!! just find a larger pulley for the SC that will drop your boost level to near 0 and you are good to go. it takes 10 minutes to change the SC belt (not sure on the pulley removal time).. that way you won't have to mess with anything else..
later
Bret
 
Not that I can tell you where to get it, but IIRC from my days in the petro-chem field, MTBE and ETBE have BOV in the 115-116 range.

If I ran the numbers right you would need about 3.3 gallons of 116 BOV fuel to bump 20.7 gallons of 87 no lead to an approximate octane of 91. I.e. 3.3 gallons per tank fill.

Not an overly practical solution. MTBE was banned in California a couple of years ago. Both smell like hospital ether.

The point is, it is going to take a significant amount of blending fuel to boost the octane over many tanks of gas significantly over a long trip.

Have you determined what your minimum octane requirement is? I.e. how low can you go without knocking?
 
My understanding is Toluene will do the same thing. Dunno where you would find that in Backwoodsville Mexico tho..........
 
Somebody please correct me if I'm wrong, but the TRD supercharger is an Eaton M90 with an internal bypass valve, right?

If so, then...

If you absolutely had to, you could place a vacuum reservoir and a check valve on the vacuum line between your throttle body and the bypass valve actuator on the supercharger. This would hold the supercharger's internal bypass valve open, keeping the supercharger from generating boost. I think there would still be some heating of the intake air, though.

I'm pretty sure that your performance would take a significant hit though, to power levels below the stock naturally aspirated output.

- Whipp
 
I drove mine the other day without the belt. It ran OK but it was a slug.

It would be an interesting test to leave the belt on and block the bypass open to compare how it runs without a belt.
 
My understanding is Toluene will do the same thing. Dunno where you would find that in Backwoodsville Mexico tho..........

Blending octane value of 111 for Toluene IIRC. You'd need about 4.5 gallons or so per tank give or take.

I like the kill/bypass boost idea better than the thought of someone hauling around a bunch of blend stock cans.
 
I am just now getting into this one, but Dan hit it on the head. Pull the belt. The vacuum will spin the rotor/s inside the supercharger housing to allow you to drive it. We have done this many times at the boat races.
 
Somebody please correct me if I'm wrong, but the TRD supercharger is an Eaton M90 with an internal bypass valve, right?

If so, then...

If you absolutely had to, you could place a vacuum reservoir and a check valve on the vacuum line between your throttle body and the bypass valve actuator on the supercharger. This would hold the supercharger's internal bypass valve open, keeping the supercharger from generating boost. I think there would still be some heating of the intake air, though.

I'm pretty sure that your performance would take a significant hit though, to power levels below the stock naturally aspirated output.

- Whipp
I agree that this solution would work. The bypass valve will not allow any pressure buildup after the SC. At a certain rpm, I suspect the SC will generate a little boost because I don't see 500cfm flowing thru that bypass valve without a bit of back pressure.

You could also mechanically force it open with a stepper motor linkage.

ST
 
It would seem to me that if you were not going to "use" the supercharger you would not want any of the engine's output to be wasted driving the screws, even if it is not boosting. That is why I wonder if pulling the belt might be the best option????
 
It would seem to me that if you were not going to "use" the supercharger you would not want any of the engine's output to be wasted driving the screws, even if it is not boosting. That is why I wonder if pulling the belt might be the best option????

I think either way (bypass open or belt removal) will be highly inefficient. On bypass, the screws will still be turning. With the belt removed there will be a strain on the intake air, essentially starving the engine and causing it to run rich (my theory).

Blarsen suggested a low-boost/no-boost pulley. I seem to remember someone posting some boost numbers for different size pulleys. With the lowest boost pulley available, what is the required octane rating to prevent knock? It would be closer to 87 the lower the boost, wouldn't it?

I'm still dreaming of getting the supercharger, so I can only suggest based on theory. Someone else would have to be the guinea pig.
 
A/C clutch?

-Spike
 
Back
Top Bottom