Stubborn Tie rods

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 12, 2008
Threads
64
Messages
522
Hello to all the great and experienced minds ( and hands) out there in MUD, I am in the process of repacing all 4 rod ends ( Tie rod and drag link) and can not for the life of me get them to release from the steering arms, the truck is a well loved 97 LX living in the very snowy mountains of BC. I have had great success with search etc on other repairs and mods but must this time humbly bow to the wisdom of others for some freakin advice!
Have tried PB blaster
Pickle fork
hammer
Larger hammer
gear puller
So before it goes into the pay for hire mechanic I hope for some help.
Guess I will need to stop the lurking and introduce my self and my travel partner before she is all finished ( next post)

Cheers Peter ( Humble Newbie)
 
I haven't done it for the 80 yet but the 60 is fairly similar and its just the castle nut and slamming between it with a pickle fork. On my 60 it was cake. On another truck we just did a suspension upgrade on it take a LOT of sledge blows to get it loose.
 
the key is to hit the steering arm, not the TRE. Take off the wheel, loosen the castle nut, but leave it threaded on a few threads so you don't bugger them up and hit the arm from the side. Should pop right off. If you are trashing them, then try a little heat. Worst case, put a pitman arm puller on it and put tension on it and then hit the steering arm. A small dead blow or small hand held sledge is the best tool. A normal hammer will never do the job right.
I keep a small sledge in my trail box :)

I remember an old harley manual that said you need a 5 lb sledge to remove a bolt....and my dad try for 20 min with a 2.5 lb sledge. 1 smack with the right tool and it popped loose.
 
Remove castle nut, grind down stud a good bit and get it HOT, then pound with 3lb sledge... if your lucky it will come out... The 5lb'r looks like it will work better.

Replaced my Relay link and was a BR%#%#$, I have the relay rod to do next and am dreading it... all because of the balljoints.
 
Thanks guys, I have had the 2.5 going on the pickle fork, I will try the hit the arm idea and then move up to the BIG hammer. I replaced the whole steering box a while back without pulling the rod ends. have avoided hitting anything I might damage, maybe I should swing away!!

Cheers and thanks again
 
I've had some rod ends that were insane to get off, lots of PB and plenty of pounding. Afterwards I thought of using an impact hammer on the pickle fork, mechanical vibration is always good. I also read where someone heated theirs up, till the bolt was red hot, then gave it a wack, they said that was the trick and it came right out.
 
Not sure if you are using one of these.

OTC Tool Manufacturer for Cars and Trucks : Products

It worked great for me when I replaced all of mine. Also it will not tear your TRE boots like a pickel fork. One sugestion loosen the castle nut but leave it threaded on a few threads. That way when it releases it will not fly up in the air.
 
Last edited:
I am a recent convert to the otc tie rod end removal tool after years of pounding on pickle forks (and tearing boots). The otc tool is worth every cent and lives in my trail repair kit in case I need to straighten a tie rod or replace an end on the trail. Removing tie rods with this tool is childs play. (With my new budbuilt rods hopefully I wont need to repair them on the trail.)
 
I "borrowed" a full front end service kit from my local Canadian Tire store. It had two sized Pitman arm pullers, two ball joint separators and a TRE remover. See this link for an example of the service kit: Amazon.com: OTC 6295 Front End Service Tool Set - 5 Pc.: Home Improvement. I managed to replace TREs and ball joints on my rusted Pathfinder with these. No hammer required. I suggest looking for the full kit either to "borrow" or buy.

And man do they POP when they let go! Neighbours thought I was target shooting!

PS: By "borrow" I meant that CDN Tire lets you take the tools for use at home for a small deposit. Your deposit is refunded in full when you bring the tools back clean. For something that I may use once every 2-3 years, this beats buying the kit. YMMV
 
Get a tie rod puller.... never had one I couldn't pop off before.
 
Not sure if you are using one of these.

OTC Tool Manufacturer for Cars and Trucks : Products

It worked great for me when I replaced all of mine. Also it will not tear your TRE boots like a pickel fork. One sugestion loosen the castle nut but leave it threaded on a few threads. That way when it releases it will not fly up in the air. After you use tool on one TRE you will see what I mean. Alot of force is released with this tool.

X2!!!

So much better than a fork and hammer!
It is great!
 
Thanks for the tips! Went and borrowed the appropriate tool from good old Canadian Tire and with a little extra muscle, some heat and a bgger hammer I have the tie rods off and the new ones on, so it looks like we are all good for the moment!
Thanks to all.

Cheers Peter
 
Back
Top Bottom