Starting Issue!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

"while it is plugged into the starter"?? ....i thought i could just put the positive to the connection from the harness and test. i'm confused. can you clarify? ....so if everything's connected where do i stick the positive probe exactly?
 
"while it is plugged into the starter"?? ....i thought i could just put the positive to the connection from the harness and test. i'm confused. can you clarify? ....so if everything's connected where do i stick the positive probe exactly?

Leroy, I thought the same thing about pulling off the lead when it wasn't starting and testing it. WRONG I found out. You need to either put a "scotch lock or connector" on wire with the plug to solenoid or poke a tester probe into the wire to test it. The failure occurs when you try to start the vehicle and you have a bad connection and when you try to turn over the starter and draw a big load it will fail. If you do not try to start the starter and create a load the unplugged wire will register around 12v every time. This had me confused until it was explained to me and I tested it and sure enough no volts under load.

Another thing I did in the meantime was got a wire and put a spade connector on one end and a round on the other (this side doesn't matter). I would unplug the wire at at the solenoid and plug in the spade and then touch the other end of the wire to the + battery and start it. The ignition key has to set to on. This way I was never stranded while I was troubleshooting the thing.

If this doesn't make sense just keep asking questions and I will try to help the best I can.
 
TOY350,
I think what you are saying makes sense. I also understand what you mean by jumping the connection directly to the battery from the solenoid. My problem now is I got home and double checked the fuses and the ground to the battery (it registered 0.4) and gave it a go and she started right up. I've started her about half a dozen times tonight and no hesitation whatsoever. I'm lost now.... I better do some searching and see what i can come up with. Perhaps heat related? Any ideas please chime in .... anyone.
 
My problem (broken and corroded wires in the NSS connector) was directly heat related. The truck would start perfectly when cold but once at operating temperatures starting was hit or miss. I think the heat from the transmission increased the resistance in the corroded/broken pins to the point where the solenoid would get enough juice to engage.

Try taking thr truck for a drive (15 mins or so) and get the engine and transmission up to operating temperature and see what happens.
 
I thought mine was heat related until one morning it wouldn't start cold. I thought mine was solved when I rebuilt the starter but a few days later it didn't start again and when I solved it you can easily see what the real problem was.

I don't know if you have already but at least crawl under there and unplug the NSS harness and look at the plug. Romer did and BAM, it was obvious.
 
I can see the neutral park switch or NSS on the left (drivers) side of the trans. the cable runs up from there and there doesn't seem to be a connector at the NSS. my truck is a '94. anyone know where the connector is?
 
Not sure if your tranny is the older one, should tell you on your vin tag which one you have.
 
Mine's a '94 A442F.... different. Started right up this morning and drove it down to work. Got here and an hour later wouldn't start. Had it towed over to a local shop I trust. I'll report back with what they find.
 
I think the connector for the NSS on an A442F is where the loom crosses into the engine bay. I think the lump you see on top of the NSS IIRC isn't a connector, the wires just go right into the casting.

I had my NSS off a few months ago and there are two contacts that move with the gear selector, 1 does the NSS function and the other indicates which gear is selected. The contacts have little springs behind them to push them against the 'tracks' (actually lots of fixed contacts that sort of make a track) and on mine the spring behind the NSS contact had turned to dust.

I didn't have a spring small enough but there was enough room to open up the spring hole behind the other contact and fit a slighty bigger spring that I did have and then use the origional spring from there in the NSS contact.

I don't know if a previous owner had chopped my NSS breather or they come like this from the factory but mine is very short and will have seen a lot of muck and water so I'm surprised it wasn't in even worse condition.

Hope this helps.
 
Shop topld me they put 12v right to the solenoid connector on the motor and got no action so they think they can rule out any of the electrical connections, ignition, fuses, fusible links and harness.... basically they think it's the starter, so they're going to change it with the warranty one I supplied. I would have liked to done the work myself but since it started multiple times last night it didn't make sense. So they get to change it and i get to pay, but hopefully this is the culprit. By putting 12v right to the solenoid that should rule basically everything else out, corrrect?
 
That should rule out the wiring issue we were talking about as long as you don't have 2 problems you are chasing, unlikely but not impossible. Good luck.
 
TOY350,
Right. if i had gotten the prong in there while someone turned the key i would have found 12v going to the solenoid and would have then proceeded to change the starter. Only i wouldn't have found that last night because it was starting just fine so there was nothing to check. Thanks for your input and I'll be putting together a stock of spare parts (fuses, fusible links, etc) for starting including a spade connector and wire to jump directly from the battery. i've learned something here and you've been a big help. thanks.
 
My pleasure, it was a nightmare while I was troubleshooting it but I did learn quite a bit. Let us know how it goes once the starter is replaced.
 
well the new starter is in.... it's beefier than the one that came out and it had a sticker that said "remanufactured in the USA". the one that came out was smaller and said "remanufactured in Mexico". They drove it a good 30 minutes and got everything to operating temperature and she started every time.
So now i'll drive it and see. If i have troubles I'll be right back here.... if i'm not posting in this thread it's a good thing!
 
Back
Top Bottom