split case hand/parking brake

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

haystax said:
There was a recent thread on PBB about someone using a 4wheeler disc caliper and machining the stock drum into a disc. I'll search and see what I come up with as I am also interested in a parking brake solution.


Read it awhile ago, did you notice that hub is off the later non split case?

Anyways, I will work on a bolt on bracket.

Rob
 
Rob , I used the man a fre disc e-brake on my orion and it seems o.k. . I would say that fabbing your own mount is best and they just had a turned down drum that is the new drive flange , a piece of 1/8 steel for the disc with the bolt pattern drilled in it , and a cheesy little caliper.
 
peesalot said:
Rob , I used the man a fre disc e-brake on my orion and it seems o.k. . I would say that fabbing your own mount is best and they just had a turned down drum that is the new drive flange , a piece of 1/8 steel for the disc with the bolt pattern drilled in it , and a cheesy little caliper.

Doesn't sound like it is worth 3 bills, plus 1 more if you don't have your drum...
 
Would it be possible to machine your own disk with the same hole pattern as your output flange, then mount the disk between the drive shaft and the output flange? I know you would need to get longer drive shaft bolts, but I don't see any other issues with the disk. As for the caliper, I was thinking a motorcycle manual caliper(as stated before). I thought about building a bracket that mounted to the bolts that hold the t-case together, the one thing I was concerned about was if the t-case would be strong enough to have a bracket mounted to it? I really would rather build a bracket that came off the crossmember, or possibly the frame depending on which is closer.

What do you guys think?

Scott
 
I think you'd be better off making a bracket that hangs off the TC, simply because one that hangs off the frame will flex with the frame, possibly binding.

You may be able to find a motorcycle front disk that is capable of being drilled to fit the output flange.

Me, I'd put it at the *rear* of the driveshaft, and bolt the caliper support to that hefty axle! Just because Toyota put the drum on the transfer case is no reason to follow suit with a disk.

Kirk
 
Very true about the flex in the frame, I didn't even think of that. I like the idea of having the caliper mount attached to the axle housing, but the only issue I can see is that puts that disk where it can get bent/crushed from rocks, mud etc... This would cause some serious trail headache.
 
Portal_tek said:
Very true about the flex in the frame, I didn't even think of that. I like the idea of having the caliper mount attached to the axle housing, but the only issue I can see is that puts that disk where it can get bent/crushed from rocks, mud etc... This would cause some serious trail headache.

OTOH, there's only 4 bolts holding it on, so if you crunch it....


Kirk
 
try to find or make a disk brake set up that mounts to the larger bolts that hold the rear cover/seal retainer to the t-case.
I have a few factory split case parking brakes and they are no better then the old FJ40 ones. I can get all the parts new and only need to do minor mods to used parts to create more kits but it just isn't worth it.
You would only have a park brake, an emergency brake would be much safer.
ps. ya, and there are only four bolts holding the factory one on.
 
Thats true about the 4 bolts, but the reason I drive a cruiser is so I don't have to do trail repairs. I hate to join the J**p club and start now. ;)
 
I got all of my e-brake stuff for the split case from Mike Bingham at Cabe Toyota in Long Beach California. Everything except the backing plate. Do be aware that the mating surface for the driveline will be moved back about 3/4" or so. So, driveline mods may be required.
 
Could you post a picture of your setup? How much was it? Do you have a contact number?

Scott
 
I added an 89 honda accord rear disc rotor. The inside dia is the same as the back of the output flange on the T-case. Built a bracket off the case bolts. Its working pretty well so far, since Rubithon last year.

Basicaly, remove the output flange, remove the dust cover and studs, place the rotor on the back of the flange and install longer bolts. No driveshaft worrys this way!!
 
Last edited:
What caliper did you use?
 
Nice, so you just plugged the hydrolic port, then used the e-brake cable from the Honda?
 
here's one.
Also just to let you know, this is about a one year old project, so memory is a little fuzzy. The caliper may be off a 91 acura integra if not the honda.
 
Back
Top Bottom