SOR Overhead Tray

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 14, 2011
Threads
11
Messages
168
Location
Baltimore
I'm wondering if anyone has installed this and has any comments?

My main worry with something like this is that one could hit their head on it if you are bouncing up and down in the seat. Also not sure how safe it would be in an accident.

I know the fact that it gets in the way of the sun visors would annoy me, but I think I would just cut off the are close to the visors preventing them from fully rotating upwards.

This is what I'm talking about: Page 278 Land Cruiser Overhead Tray - https://www.sor.com/cat278.sor

Thanks
 
It seems that that vendor isn't dealing directly with the public anymore, and his parts distributor doesn't list any overhead trays for the FJ40.


If anyone else has experience with the SOR over head tray, I would be grateful for any feedback, especially on whether or not one could hit their head on it.
 
This is Kevins email; awlteq.metal@gmail.com

and a photo he sent me a year ago.......


1615924568810.webp
 
It seems that that vendor isn't dealing directly with the public anymore, and his parts distributor doesn't list any overhead trays for the FJ40.


If anyone else has experience with the SOR over head tray, I would be grateful for any feedback, especially on whether or not one could hit their head on it.


Do you have a link to the parts his distributor is selling? I was lucky to get one of Kevin's FJ45 tailgate and valence for under the tailgate. Can't beat the quality for aftermarket parts.
 
I have something similar I built out of wood 10 or 12 years ago. I would say if you are wearing a seat belt it would be hard to hit it unless you are well over 6 feet tall.
On mine, the visors fold up to the bottom like the one on S.O.R. does.
 
I have something similar I built out of wood 10 or 12 years ago. I would say if you are wearing a seat belt it would be hard to hit it unless you are well over 6 feet tall.
On mine, the visors fold up to the bottom like the one on S.O.R. does.

I also have one I built from wood. I jammed it in the space between the rails and the ceiling, and then I held it in place with small metal C-clamps. It worked very well, but I never liked how the sun visors wouldn't fold up all the way. I found it really distracting while I was driving. My current plan is to get the SOR one and then cut away the metal that is preventing the sun visor flaps from going up all the way. Then I'll just paint it.

My concern with the SOR one is that it looks as though it sits a bit farther back than does the wooden one I built, and I was concerned it would be too close to my head. I'm not super tall, but am about 6'.


Do you have a link to the parts his distributor is selling? I was lucky to get one of Kevin's FJ45 tailgate and valence for under the tailgate. Can't beat the quality for aftermarket parts.

Yes, this is it: Wholesale Offroad Parts and Accessories - LANDCRUISER PARTS | 4wheel Auto - http://www.4wheelauto.com/

I was told that you can contact them and they will act as distribution for his products.
 
I have the SOR tray and love it, it's great for holding random items out of the way and out of sight, plus it gives me a place to mount speakers. I have been planning on adding a front face to it to install a stereo/ham radio/switches, but for now it's just stock. I liked it so much I made a matching tray for the rear of the cruiser to mount the rear speakers and for holding other items out out of view.

I've never worried about hitting my head on it, you'd have to be freakishly tall and sitting really close to the steering wheel for your head to come anywhere near it. I also never noticed any problems with the sun visors, they flip up against the bottom so it's mostly out of the way.
 
I've never worried about hitting my head on it, you'd have to be freakishly tall and sitting really close to the steering wheel for your head to come anywhere near it. I also never noticed any problems with the sun visors, they flip up against the bottom so it's mostly out of the way.

Thanks dtg, that's exactly what I was looking for.

I still think I'll end up cutting away a space for the visor though. I have one I made out of wood that works about the same way, and I was always annoyed by the visors being up against the bottom. It's such a pitifully small windshield space to begin with that any loss of real estate is noticeable.
 
I have the SOR unit as well and my experience is similar to DTG. It is so far forward that in normal operation it’s just not an issue. The visor rests against the bottom of the tray as previously stated but it is not block anymore of your view than it normally does when folded completely vertical. I don’t know how you could possibly trim the shelf to help that situation. As to your concerns of it being an additional obstacle during an accident, it is too difficult to predict that scenario. I will say that the tray has no sharp edges facing the passenger compartment and if one is wearing a seatbelt it would be exceptionally difficult to impact the shelf. I hope this helps.
 
Cool! Looking good.

When I made mine I used pine for the bones and then covered it with wooden wall paneling, the kind that has the stripes on it.
im sure his wife likes that on the counter... but i woudl do exactly the same.

hehehhe
 
Working on one now, cherry front. Some lamps and speakers underneath, place for stereo and 2 cubbies....

View attachment 2617215

View attachment 2617217


What material did you use for the speaker enclosure? Probably going to do something think like this with a overhead tray I bought years ago from a wrecking yard. Thinking need a very dense material to keep it from sounding tinny.
 
right now just a wood box covered on top w a piece of foam insulation i had laying around. I did just spend $8.99 on speaker baffles, should b here by friday.
Cheap speakers and unit btw......... guessing music in Fiona Joy is going to be highly impacted by her off pitch but loud signing.......
1616018031425.webp
 
What material did you use for the speaker enclosure? Probably going to do something think like this with a overhead tray I bought years ago from a wrecking yard. Thinking need a very dense material to keep it from sounding tinny.

When I made my wooden box, I didn't use any baffle at all and it worked out well for me. The whole box was open on the inside and acted as a sound chamber for the speakers and made the bass response much louder than if they were baffled. It would only become an issue if you were thinking about putting really big beefy speakers in there, as you might start to get too much stray ringing.
 
OK, found this thread while contemplating building an overhead console. I have the SOR shelf (installed by the PO). Would like to run wires for winch and locker control to the overhead. Is there a way to run wires from the passenger side engine bay to the overhead without drilling a bunch of holes? I just tried running a wire down the B pillar, but it stops where the top meets the tub (approx.)... is there an opening in there, or is it solid? I assume the A pillar blocked too? If I could fish wires up the B pillar, then I might be able to piggy back on the stock harness through the firewall (would have to pierce the rubber apron on the grommet is all).

for those with overhead consoles, howd U doit?
 
OK, found this thread... cool! Looks like I can fish them up/down through the drivers side A pillar. Looking at the firewall on the drivers side, it appears there is actually a rubber nipple that may have been intended to pass some wires through?

Can someone confirm what this is for?

FirewallNipple.webp
 
Back
Top Bottom