Shaky 80

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Do it.

Old, cheapo, no name tires suck. You'll notice an immediate improvement, even if it turns out that's not 100% of the problem.

Curtis

I'm pretty sure i'm going to just drop the money and order the tires and wheels on Monday. And hopefully by the time they show up, my steering damper will have been installed.

The shaking does keep me awake when I drive, but I'm worried its going to shake my truck to death. i already have several rattles in the truck that are becoming more pronounced every time I get it up to highway speeds.
 
here are a couple pictures of the shaky 80
Dixie II mescalero sand dunes.webp
Dixie II sand dunes.webp
 
Did you check to make sure the steering arms are tight? Also Trunion Bearings.

sure have, I've checked them several times
 
I've been working my way through these same troubles. ('84 bj60 3" belton lift 386KM) and next up on my list is an knuckle rebuild. sky manufacturing in OR supplied @ a reasionable price. $50 w/ NSK trunion berrings.
 
I've been working my way through these same troubles. ('84 bj60 3" belton lift 386KM) and next up on my list is an knuckle rebuild. sky manufacturing in OR supplied @ a reasionable price. $50 w/ NSK trunion berrings.

well its nice to know that I'm not the only person right now with a shaky cruiser. :cheers: hope it works out for ya:beer:
 
I agree with the suggestions to get new tires;
That is where I would look next, after all you have already done.
Tires can slip a belt causing un-fixable vibrations, that is until you buy new tires. And some tires
are just bad from the factory.

A bad steering stabilizer should not cause shaking; it is not there to reduce shaking,
it is there to decrease rapid movements of the steering stuff when you are on uneven ground
or hit a bump with one tire, etc. I have found when mine gets worn out the vehicle tends to wander
just a tad more than when the stabilizer is new.

Good luck.
g
 
Checking in on the progress!

I had a bad irritating shake at 55-65 on my pickup. I had checked many things, aligned the front end after replacing rod ends, and more, couldn't eliminate it. At the time, I was running Truxus MT's in relatively good condition. I was going to go on a long trip so I changed them to BFG AT's and no more vibration. I'd go with new tires too if you're at all suspect of them.
 
BTW;
The OME steering stabilizer works better than the OEM, IMHO.

I also changed all my motor mounts and tranny mount due to
a rumble/vibration when in gear (but not moving); no difference.

g
 
I also vote tires.


Could be worth a check in your drive line though. lock you CDL and pull the front drive shaft....drive and see if it shakes.
Then pull your rear drive shaft (after you put your front back in ;) ) and test drive it again.

If the PO warped the rotors he might have overheated the wheel bearings...

Oh yeah about the steering stabilizer, Mark W from TT tech articles says he has yet to see an OEM one ever wear out. Plus putting a steering stabilizer on to stop a shake is just band-aiding the real problem.

good luck...

-Al
 
I also vote tires.

If the PO warped the rotors he might have overheated the wheel bearings...

Oh yeah about the steering stabilizer, Mark W from TT tech articles says he has yet to see an OEM one ever wear out. Plus putting a steering stabilizer on to stop a shake is just band-aiding the real problem.

good luck...

-Al


i'm certainly not trying to band aid any real issues, just trying to narrow things down a bit. I'm really certain that is a combination of tires, rotors, and the steering stabilizer. I've already done the wheel bearings.

The old wheel nearings didnt look distorted, but had very minor gawling on some of the rollers. If I hadn't pulled it apart to do them, I would have just repacked and put in new seals and felt comfortable.

I know it sounds stupid,but I'm still felling like it might be my rotors. The 1991 FJ80 has fixed calipers that mount directly to the knuckle. I figured that what might be happening is that the rotors are dragging and warping as I obtain higher speeds. I can rest my foot on the brake and feel feedback through the pedal. Its about (not completely) as consistent as the tire slapping that I hear on the asphalt.

If rotors, new pads, and steering stabilizer don't fix it, then I'm just going rebuild the front axle. I'll inspect axle shafts at the same time.
 
I vote tires also. Out of all the shaking experiences I've been through, its always been the tires. Even when they have been balanced twice, rotated and dyna-beaded. Changed the tires-no shake.
 
ok, so I replaced the steering stabilizer today.Nothing changed. :rolleyes: The factory Toyota unit was actually operating fine. I compressed and extended it manually and it appeared to function normal with no dead spots or unusual movement.

I went by discount tires today also. I called at 09:00am, at 11:00am, 1:00pm, and 4:30pm and finally when I never got a call back :mad: I went down there myself so they couldn't ignore me. They wouldn't match the price that I got from 4 wheel parts ( i thought they had a price match guarantee?), so my tires and wheels are ordered through 4 Wheel Parts and should be here by the end of this week or beginning of next. And since I bought the tires and wheels, I couldn't help myself. I ordered the lift too. OME Heavies front and rear.:DI'll have the tires to slap on to verify my shaking issues. Hopefully thats it. And the lift wont go on until I move into my new place the following week and the shaking is gone.;p i think the shaking will be present until my new rotors arrive.

tires are 315/70R17 Pro Comp Xtreme Mud Terrains
wheels are 6x5.5" Black Steel Wheels w/4" BS

bought a set of 5
 
I would do the following:
- drop front driveshaft, drive it around, repeat for the rear
- replace tires
- lift it

If all that doesn't work...59mph baby!
 
so if the tires balance perfectly how could it be the tires? You guys are asking him to spend north of $1,500 to "hope" that fixes it, then start replacing motor mounts, knuckle rebuilds, shocks, springs, ect..... That's just crazy!

i didn't read if he had a lift or not, but it could just be death wobble. Check bushings, wheel bearings and trunion bearings first. Put it on an alignment rack and see if anything is out of spec.
 
concretejungle,
Thank You for your concern. I have replaced wheel bearings, steering stabilizer, aligned it, rotated the tires, had them balanced (by a shop that may have just taken my money). I've checked the trunion bearings and they checked out ok, no unusual movement. I have replaced all the tire rod ends. lets see here, the list goes on. if you look at the beginning of the thread you can read a more detailed list of things that have been done, and what I want to do.
A set of tires and wheel shipped to my door is going to be $1400.00. If I didn't think I was getting a deal I probably wouldn't have bought them just yet. The OME Heavies with shocks are another $500.00

When my new tires are put on, I am going to have them road force balanced. Does anyone think that since I didn't have it done this way the first time, tire separation may now have shown up in a previous balance?

right now I'm waiting on my new rotors to show up in the mail. Front driveshaft will probably come off tonight.

Does anyone think it would hurt it to drive around for very long? will it hurt anything to take it about 65mph with the front DS off and CDL engaged?
 
When my new tires are put on, I am going to have them road force balanced. Does anyone think that since I didn't have it done this way the first time, tire separation may now have shown up in a previous balance?


It is most likely they just "static" balanced your tires without spinning them at high speed.

every "speed specific" shake or wobble that I have ever had was tire related. My guess is you have a some belt seperation going on at speed.........paticularly when you say it goes away again at higher speed, I think if it was mechanical it would get worse.
 
alrighty then, one more day of trouble shooting. I pulled off my front drive shaft. no change in vibration. but i think I'll keep it off until I put on my suspension lift here in the next couple of weeks; I hope!

I had my uncle drive along side me today on the highway, and he could see the tires bouncing up and down like tire separation. :eek: and on my drivers front wheel, he noticed that it might actually be bent.
since the vehicle shows signs of a previous accident, I think this might be a strong possibility, as well as the fact that this is the wheel that has thrown wheel weights off too.

I'm still waiting on the new rotors, and I'm anxious to have the tires and wheels show up.

hopefully I will get to the end of the shaky 80 syndrome. :cheers:

on a side note. I was very impressed with how much torque this 3FE has. I did a "brake stand" on asphalt and had one of the rear tires rolling pretty good. I am very surprised at how much altitude the front end gets at the same time this is done. :rolleyes: my boss couldn't believe that a stock 3FE with 32's would do such a thing.
 
Back
Top Bottom