Shackle angle issues / questions

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 17, 2003
Threads
60
Messages
589
Location
Edmond, OK
Hey all...

I have the TPI 2.5" lift on Buddy now and my shackles are almost perfectly straight up and down with no angle out :mad: I don't want to go with another lift as these springs are still good -- albeit a bit short :rolleyes:

I have thought about doing Woody's mod of moving the shackle mounts inward to gain good shackle angle AND putting on 2" extended shackles to make up for the new angle and gain just a bit of lift.

Can I do this to the front hangars as well?? Will it still be safe?

What are your opinions? The only expense would be 4 new 2" extended shackles and a Cobalt drill bit. That's pretty cheap for better shackle angle and a bit of lift to clear my 33x12.50s.

Jody.
 
The longer shackles in front will have a much greater effect on handling than reworking the front angles....you will mess with your caster and create a bit more leverage on the suspension as you turn, making things feel sloppier...even with new poly bushings.

IMO, mod both ends, but leave the front shackles stock or only 1" over....
 
Do you think with only 1" over shackles FT/RR it will lower my current lift by moving the mounts in??
 
really, hard to say....the lift lowers regardless, and since the relocated mounts allow even longer shackles to "swing" more during articulation, your odds of a tire contacting the sheet metal increases.

I could easily stuff a rear 33" tire with my 4" skyjackers and the relocated shackle....stuff HARD into the rear fender....
 
Why not do a shackle reversal and then the added shackle length will help you caster situation instead of hurt it.

Just a thought
 
haystax said:
Why not do a shackle reversal and then the added shackle length will help you caster situation instead of hurt it.

Just a thought
Jody, if you think about a shackle reversal let me know, I've got one on the way from Faultline Fab you can look at. I HOPE to have installed by next weekend.

My only thought, that I haven't seen covered above, is when you do wear out or get tired of the TPI's and order, say a HFS spring which is longer, you will have to redo all the work you are about to do now. $650 is a big chunk of change for four 2.5" springs (but not to man of your means :D ) but in the long run it may be easier to do the simple job once.
 
Outback said:
Hey all...

now and my shackles are almost perfectly straight up and down with no angle out :mad:

Jody.

If the angle is the only problem, I wouldn't worry about it. My experience is that the effect on ride quality is minor, but it will limit the droop a little. Other people may disagree, but I did the experiment and I don't think it is worth the effort to fool with it.
 
Yeah, I think you're right Mike. I don't think I'll mess with it now -- as PinHead suggested.

I eventually want to go with some 4" HFS springs. Yeah, I'll wait.

Okay, everyone go on about their business... nothing to see here :cool:

Jody.
 
haystax said:
Why not do a shackle reversal and then the added shackle length will help you caster situation instead of hurt it.

Just a thought

Remember that with a shackle reversal and extended length shackles you will increase the caster angle which is great for handling but it will point the pinion down causing inevitable problems with driveshaft vibration or possible u-joint binding or even braking a pinion.

I have BTDT. My V8 moved the tranny & TC forward approx 3 inches which when combined with a 4"lift caused bad d-shaft angles and all above mentioned problems. I solved with a FJ60 double cardan-type driveshaft & a cut and turn of the axle. Major PIA but it's now done right.

My point is that a spring reversal creates a whole lot of issues that need to be addressed to be done corectly. These are some of the reasons so many people hate them. If I were do do another I would only use the series 2 design by BTB. The early series 1 were rock dfinders, later series 1 had all the abbove issues and more, while the series 2 adresses nearly everything but d-shaft slip joint length. But that is another story. Sorry to pirate your thread. I just wanted to share what I have so painfully learned about sterring correction kits.
 
If you've got power steering on your rig {IIRC you do} then you could consider a two-stage shackle like the Downey cantilever. That would give you a built in kick back on the upper half and a long angle on the lower half. Those are what I have on the front of my 40 and I like the ride quality A LOT. :)
 
65swb45 said:
If you've got power steering on your rig {IIRC you do} then you could consider a two-stage shackle like the Downey cantilever. That would give you a built in kick back on the upper half and a long angle on the lower half. Those are what I have on the front of my 40 and I like the ride quality A LOT. :)

I have a similar problem. My front shackles are nearly vertical.
I am looking at Downey's Cantilever shackles on their web site. My truck has Saginaw power steering, and I had to put a small notch on the shackle hanger up front so I could bolt the steering box in.
 
Of course I have PS Mark.... Got the pump bracket and early model column kit from you!!! :D

I'll look into those cantilever shackles. May be a good idea.

Jody.
 
Back
Top Bottom