Scanguage Engine Temp Range

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 18, 2008
Threads
7
Messages
13
Location
Friday Harbor, WA
I have been monitoring this board and have been searching for the answer to my Scanguage readings...what is the optimal range for the Engine Temp and what is the level where I start to look for issues. I normally run at 186 during the winter months, but have been approaching 205+ during the summer with the AC on.
My LC is a '97 with 86,000 mi, original clutch and radiator
 
Mine usually runs in the mid 180's to the low 190's in the summer. If your cooling system is in optimal condition, your temp should remain around the mid 180's unless you are towing something, or climbing steep hills. If you get above 226 (I think) your AC will cut out. Your temp is a little higher than it should be. A flush, new fan clutch and thermostat would't hurt.
 
Last edited:
mine is normally 187-190 going up steep inclines it will approach 200
 
186-193 in normal drive, though I have seen as high as 207 recently when I was in Pocono, PA on miles of 18 degree climbing.
 
Right now in the NH summer (not too warm), I get a pretty consistent 181F. Even when wheeling with the AC on, I've never seen it above 183F.

I've done a few things things to the cooling system.

- Blue fan clutch mod
- Removed radiator and power flushed it
- Replaced all the foam around the radiator (with foam bought at Home Depot)

Before doing that, the temp was about 10 degrees higher in the low to mid 190's
 
Both my '96 and '97 read between 186-193. When they're both stopped w/ the A/C on is when they hit 193. The highest reading I've ever got was 204 on the '96. It was loaded down w/ camping gear, AC on and going up a steep hill.
 
Right now in the NH summer (not too warm), I get a pretty consistent 181F. Even when wheeling with the AC on, I've never seen it above 183F.

I've done a few things things to the cooling system.

- Blue fan clutch mod
- Removed radiator and power flushed it
- Replaced all the foam around the radiator (with foam bought at Home Depot)

Before doing that, the temp was about 10 degrees higher in the low to mid 190's

That's interesting. I am looking to the ways to lower mine. Was the blue fan clutch helps? I thought the fan is not supposed to be on during the 40 mpg and above. Would also love the get details of your foam around radiator change, any picture?
 
Last edited:
Mine has been sitting at typically at 160 ish - which is weird since the thermostat isn't supposed to open until around 185 degrees....

Takes 15+ mins to warm up as well.

I'm also burning a little oil - my best guess is the thermostat is knackered and the engine isn't getting to temp and sealing the rings properly...

New thermostat going in this weekend - once I get that in and it's running at temp I'll run a compression test.
 
Here is San Fernando Valley the ScanGauge typically reads between 182ºF and 193ºF. The hottest I've seen it, with no other coolant issues like a leaking hose, is 216ºF and that was taking the Baker grade going to Vegas with the A/C off "just in case".
 
Here in Ohio I run between 186-193, although I typical run at 190 on the interstate.

In the last four months I have been slowly doing cooling system maintenance. A flush and fill with Toyota Red, new OEM main hoses, OEM thermostat, a new OEM rad cap, and a blue hub fan clutch. I still need to do the PHH and replace a few other hoses. I am currently debating about whether or not to power flush the rad. or replace with a 93' brass rad.

I am interested in the foam around the radiator and what exactly its purpose is.

Before I started to refresh the coolant system I was seeing temps about 2-4 degrees higher.
 
Here in Ohio I run between 186-193, although I typical run at 190 on the interstate.

In the last four months I have been slowly doing cooling system maintenance. A flush and fill with Toyota Red, new OEM main hoses, OEM thermostat, a new OEM rad cap, and a blue hub fan clutch. I still need to do the PHH and replace a few other hoses. I am currently debating about whether or not to power flush the rad. or replace with a 93' brass rad.

I am interested in the foam around the radiator and what exactly its purpose is.

Before I started to refresh the coolant system I was seeing temps about 2-4 degrees higher.

I read that the little foam piece is to help keep air going through your radiatior and not escaping up and over your rad. I have the same little piece of foam on my 08 tundra. on my 95 landcruiser its getting pretty flimsy so I am gonna get some expanding foam and trim to fit and paint! :hillbilly: But I have seen some put in a custom peice of aluminum or tin of some sort!
 
My gauge is normally stuck dead on 179-181 for most driving. Climbing steep hills on the highway in the hot hot desert will bring me up to 220. My cooling system is in good shape except I need to replace the fan clutch.
 
Prolly about right

I have been monitoring this board and have been searching for the answer to my Scanguage readings...what is the optimal range for the Engine Temp and what is the level where I start to look for issues. I normally run at 186 during the winter months, but have been approaching 205+ during the summer with the AC on.
My LC is a '97 with 86,000 mi, original clutch and radiator
With my cooling system flushed, happy, and up to snuff (original fan clutch) I typically ran 184, until I put 33's on, and now I typically run 186. Your area is more humid in summer so, less evaporative cooling than mine. (Uh, oh, prolly opened up a can of worms here) Your temps look to be average to good for your vehicle mileage, condition etc. I watch my coolant temps thru all kinds of conditions, and from what I have studied of the exhaustive discussions posted here, my rig performs "correctly" given the parameters of operation for this system. From what I gather, the range is: 183 being the average lowest stock readings...203 being the "middle" heat range (nice and warm) for A/C, towing, hills, summer humidity, etc., and 223 being the point at which A/C kicks out. So, 40 degree swing during operation. YMMV.
 
Last edited:
...details of your foam around radiator change, any picture?

Hey, wxm. I couldn't find any pictures taken with the radiator off, but here are a few recent ones.

Picture 1 - The stuff that I used on the top and sides of the radiator. It's just sticky-backed 3/4" x 7/16" Rubber Foam Weatherseal that you use for sealing doors etc. The foam that I used on the bottom of the radiator was much thicker; probably 2" square or so, but less dense. I don't have pictures of it, but this big piece of foam (also purchased at Home Depot) goes above the front crossmember (you can probably see the factory piece of foam by looking just above your power steering cooler).

Picture 2 - The top seal on the radiator. I used two strips of foam to bridge the gap. You could find thicker pieces of foam and I've seen a couple of people use "GreatStuff" expanding foam, but that's a bit too permanent for me (I've also read that GreatStuff can hold in a bit of moisture and cause corrosion).

Picture 3 - View facing forward from the passenger side. You can see a bit of foam on the side around the wire loom.

.
11.webp
22.webp
33.webp
 
Cool. I will check it out at home depot. Many thanks, Josh.:)
 
Back
Top Bottom