scangauge plus yellow box

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 16, 2011
Threads
118
Messages
450
Location
olympia wa
for xmas i got a scanguage 2 i also got a set of new 255/85/16 tires. the p.o. had 285/75/16 on and has installed the yellow box. now my question is should i calibrate the yellow box to the new tires and then would the scanguage be right? i can calibrate the scangauge but if i just use the yellow box then the scangauge and my speedo will read the same right?
 
your logic sounds accurate to me - the yellow box corrects the signal from the Tcase and sends it to the speedo and to your ECU. Your ECU sends signal to the OBD-II. So, the scangauge should be receiving the correct signal w/o you having to change anything in it. Make sure to use a GPS to dial in the yellow box.
 
The Scangauge will provide accurate speed. Calibrate the Yellow Box to match if you want you speedo and Scanguage to match.

I have both and don't provide a reading off Scangauge as I have the Yellow Box calibrated to read about 1 mph over actual speed. Not really intentional, I just didn't feel like messing with it again and reading a bit high provides some buffer to the radar gun once you forget about it....
 
The scangauge just reads the speed from the ECU as Ali said. If the ECU is getting the wrong speed (different sized tires or gears), the speedo and scangauge will be wrong as well. Correct the signal from the tcase to the ECU and everyone will be happy.

My speedo and scangauge read the same and are both wrong, about 8% high (reads 70 when I am doing 65)
 
right now my speedo is off by about 2mph according to my gps. ok i guess i got some math to do.
 
I have the same setup and yes it all works fine. There is a site with a java app that does the calculations for you. Put in the stock tire size then your new tire size and it gives you the ratio you need for the dip switches on the yellow box. I don't have the link off hand but I will look for it in a bit.
 
here is a kinda dumb question but ill ask it anyway. since the p.o. installed the yellow box i really have no idea where it is. is there a certain spot it might be? i think i saw a thread that said behind the glove box. also he has calibrated to the 285/75/16 so when i do this that should be the size i put in as stock right?
 
Yes the wire that the YB splices in to is behind the glove box. I tucked mine up under the glove box so I can easily get to it if I ever change tires or gears. Might want to just get on your back in the PS foot well and see if you can see it.
 
turns out after i found an app the to tell me the % of the tires it just said "nan" so i guess im good. it seems to be off from gps but its lower so im good.
 
The scangauge just reads the speed from the ECU as Ali said. If the ECU is getting the wrong speed (different sized tires or gears), the speedo and scangauge will be wrong as well. Correct the signal from the tcase to the ECU and everyone will be happy.

My speedo and scangauge read the same and are both wrong, about 8% high (reads 70 when I am doing 65)

FYI, not clear if you realize this already, but you can set the scangauge to display the corrected speed/distance.
 
turns out after i found an app the to tell me the % of the tires it just said "nan" so i guess im good. it seems to be off from gps but its lower so im good.

Not sure if you are being sarcastic, but "nan" means "not a number" and usually means you are trying to divide by zero. I would double check that you have all of the fields filled in.
 
FYI, not clear if you realize this already, but you can set the scangauge to display the corrected speed/distance.

I did not, but haven't played with it too much either. Thanks for the info :cool:
 
Folks sorry to revive this thread but i purchased the yellow box with the harness option and i'm trying to figure out how to calibrate it if you are re-geared. I'm running 315's with 4:88 gears. Does anyone know?
 
Tire Size Comparison
Specification Sidewall Radius Diameter Circumference Revs/Mile Difference
275/70-16 7.6in 15.6in 31.2in 97.9in 647 0.0%
315/75-16 9.3in 17.3in 34.6in 108.7in 583 11.1%
 
The gears don't change the process. Just calibrate the odometer to a mile marker or the speedometer to gps. Trial and error worked for me, I used the mile marker method. Your probably reading about 10% lower than actual.
 
Back
Top Bottom