RTH front door lock stuck

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

You'll probably need a slim jim to pop the latch without pulling the door panel. Otherwise it's pulling the panel...
 
I'm guessing you can't physically take the door trim off?

Your best bet would be to remove the weather stripping so you can have a good look at what's going on.
 
sounds like the return spring on the door regulator broke.
i don't have all the proper nomenclature, but there is a small spring that holds a lever up. when that spring fails the lever does not return to the position it needs to be in. bumping the door and playing with the lock button or with the key in the door is only crap shoot i found to get it open. once the door is open the panel comes off and you should be able to see/find whats going on. in my case the upper portion of the spring was still dangling in place and i found the other end laying in the bottom of the door. after that it was drive around looking for a replacement that would do the thing. my solution works, but i couldn't find the right length in the a strong enough spring. so i found a slightly longer and stronger spring and made that work.
sorry no pix, my fix was later on a sunday night and needed to rolling in the morning. so just figuring it out and getting it straight was priority.
 
hit up some of the local vendors for those parts. I may have one so let me look around tonight and I might be able to get one sent to you for the cost of shipping
 
take a picture of the part you need...I know I have at least one lying around...
 
This just happened to me too. Driver door of course.

Inside handle has no resistance. Outside handle has no resistance. Feels like the little rods they move aren't even connected inside.

Lock goes up and down. Feels and sounds right. But door won't open. I'm pretty bummed out.

Good to hear that those before have figured it out somehow!
 
I did battle with a stuck door for two full days. I took out the weather strip and wound the window down. Eventually I even stripped the drivers door to see how things work. Peep down the opening left by the weather strip using a torch. You are standing outside the car. Underneath or to the side of the lock you should see a tiny tab protruding. The issue is that you need to use a stiff rod, ( I don't know how else to put this...) I got hold of about a 6mm piece of rebar. Just pushing on this little tab does not do the trick, you need to give it a thump with a rubber mallet. In my case a piece of thirty year old grease had dislodged and jammed the little tumbling device in the lock.

I know I am as clear as mud here, good luck!
 
on mine, once i fooled around and got the door open i removed the inside door panel and had access to everything. but i could not open it with a slim jim or anything like that. I ended up buying just a random spring from the hardware store and its worked since then. apparently almost 2 years now that i see the dates in this thead
 
if i recall correctly, i rolled the window town and pulled up the window seal. then reached in there with a long screw driver and pushed the part that opens the door.

for the life of my I can not find a picture of what the door latch looks like inside of the car. When u are able to get a the window down and look inside of the door, on the B pillar side, where the door latches, you will be able to see the mechanism that holds the door shut. make sure the door is unlocked and you should be able to reach down to that mechanism and actually push the latch open to get the door open.

once the door is open, i removed the door panel, rolled the window back out and removed the door latch assembly to replace the broken spring. try and look into the door that you can get open to understand how the mechanism works and that might be able to help you figure out which part to push on with the screw driver.

Good luck with your work.

*edit: added info
 
Last edited:
image.webp
Updates!

Getting the panel off with the door shut was easy. From there I was able to get in and take a close look at the lock/latch mechanism.

Luckily I had an extra!
 
For many days I pulled on the piece on the mechanism. It was stuck for some reason. I pried on the door. Banged. Kicked. Nothing. For days.

Finally I gave up. Temporarily.

The piece on the mechanism compresses a little spring that's inside the mechanism itself to release the latch. I could feel that the spring could t compress for some reason.
 
Back
Top Bottom