Ring and pinion pattern okay?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 8, 2009
Threads
61
Messages
439
Location
North Saanich, BC, Canada
Hi Mud :) Putting a used 60 series R&P into my 80 third... 3.70 ratio. Never set up gears before, do the gurus here think this is an acceptable pattern? Maybe a little close to the root on the drive side, but if you look at the residue paint a few teeth down, it looks fairly centered. I think coast is okay, a little to the toe but I think that is acceptable? Thoughts???

IMG_1384.webp


IMG_1382.webp


IMG_1383.webp
 
Slightly offset yet to my liking, but I only have 4 to my name, so not like I'm Zuk or the guys at Just Diffs - but also I see the paint doesn't look like you're "forcing" it enough (paint 'dent' should show near bare metal).

Have you done this before & this is just your 1st 'Yota? Or new to this all?
 
If it worked OK in the FJ 60, then it should be fine in your 80. All you have to do is swap 3rds, no need to do a "gear setup"!

This too - I read it as though you swapped the gears alone - but if it's the complete 3rd, I'd leave 'as is'.
 
No no, not swapping complete 3rds. Setting up the used R&P from scratch. Haven't set up gears before, no... new to gears completely. I will go out and force it to dent the paint more and see how that turns out, thanks.
 
Got a bit more paint to rub off on the drive side... Coast side has a much softer pattern, can't seem to get much more paint off. Drive side looks fairly centered, just concerned there appears to be zero contact near the top of the teeth. Maybe this is okay? Teeth must be weaker near the top anyway...............

IMG_1385.webp


IMG_1386.webp
 
I would be looking to pull the drive side contact more into the centre of the teeth.

Does this mean more or less pinion depth shim? More would push it closer to the toe of the ring (I think) but also deeper to the root... which might not be good...

So whatcha gunna run in the front diff?

Either Marks or genuine 3.73. Probably Marks because they're about half the price.
 
Does this mean more or less pinion depth shim? More would push it closer to the toe of the ring (I think) but also deeper to the root... which might not be good...



Either Marks or genuine 3.73. Probably Marks because they're about half the price.


More shim - need to drive the pinion closer to middle of ring gear.

Looks better getting the paint to 'print' deeper. ::EDIT - looks clearer, shows the issue of needing to move pinion inboard::

So is the ratio close enough if you drop the trans into lo & lock the trans? I've never ran different ratio gears, and it seems 3.73 / 3.70 is dang close - is close good enough when you lock up though?
 
More shim - need to drive the pinion closer to middle of ring gear.

Looks better getting the paint to 'print' deeper. ::EDIT - looks clearer, shows the issue of needing to move pinion inboard::

So is the ratio close enough if you drop the trans into lo & lock the trans? I've never ran different ratio gears, and it seems 3.73 / 3.70 is dang close - is close good enough when you lock up though?

Thanks, I'll go add a shim and see what happens. My truck is part-time with a Marks spool in the transfer case and unlocking hubs, so 3.73/3.70 won't be an issue. Assuming I'd be stuck and spinning a tire before I engage 4wd anyway.... ratios within 1% will not be noticeable. Actually, I read somewhere that within 1% is considered acceptable even for AWD! Not sure I'd be comfortable with that myself, but for part-time, no problem. One day, if I'm feeling rich, I could put genuine 3.73 in the rear but they're kinda pricey when used 60 gears are a dime a dozen...!
 
I'd go back to where you were on the pinion and adjust backlash down until you can drop that contact down towards the toe.

Which direction do you think? I tried 0.005 and 0.012 backlash and neither seemed to change it too much... Not sure if I should be going outside that range???
 
No I would not deviate beyond .005 to .010

Hows your carrier bearing preload?

You should be able to dial that contact in by moving ring closer to pinion if all else is correct.

Do you trust your dial indicator?
 
Back
Top Bottom