Real time help 95 died while driving.

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Nut on the back of alternator had come loose causing the wires to over heat. No fuses blew relays were all fine fusable links are still all working. Replaced the corroded and burnt wires everything works.
1444692426433.webp
 
This is exactly why many of us keep spare fusible links and efi relays.
Now I'm curious how common ignition switch problems might be. Don't recall hearing of any here on mud.
 
Given the condition of the alternator connection, I would replace the fusible links anyway. Keep the original as a spare. You're only looking at around $10, less than a pizza and a lot less than a tow... Our vehicles are all in the 20yr age bracket - best to replace things that are known to cause total stoppage of the vehicle in the comfort of the driveway versus out bush...

cheers,
george.
 
The ignition switch is fine this was the whole problem.
 
HUH? - the alternator bad connection would not stop the CEL from lighting up if the battery is still reasonably charged. So, I would still CHANGE the fusible links...

cheers,
george.
 
Listen to @george_tlc . He's an electrical guru of sorts when it comes to these rigs (& I'd imagine all things 12V). Click on his link in his sig & see for yourself!


Btw, thanks for showing the end result!
 
I don't know the only thing that changed is that connection and I just drove 200 miles no issues. Same relay all same fusable links. I will replace them as they look worn but they were not the issue this time.
 
Does your CEL come on now when the key is turned to on?
 
Toyota par
I don't know the only thing that changed is that connection and I just drove 200 miles no issues. Same relay all same fusable links. I will replace them as they look worn but they were not the issue this time.

You stated your alt was putting out more than your battery was getting. Was that issue addressed?
 
HUH? - the alternator bad connection would not stop the CEL from lighting up if the battery is still reasonably charged. So, I would still CHANGE the fusible links...

cheers,
george.

The reason the alternator connection can cause this problem isn't at all obvious until you look at how Toyota wired up this part of the power supply circuit. The circuit goes from the + terminal on the battery through the Main fusible link down to a splice located at the back of the alternator. Then from the splice there's a wire that runs to the fuse block that powers, among other circuits, the ECU-B circuit. The splice can deteriorate and develop increased resistance leading to heating and further deterioration until the point that insufficient current flows to the fuse block and a bunch of circuits then loose power. Post #41 shows a picture of the splice and nearby terminal for the alternator and you can clearly see the overheating and associated discoloration that's occurred. And here's another thread from 2007 describing the exact same problem: Real time help.

In my opinion it's a flawed design by Toyota. They were trying to address the issue that several of the circuits the splice wire feeds can draw a lot of power (e.g., 40A heater blower, 30A door locks, 20A defogger...) and thus feeding directly from the alternator ensures an adequate power supply. But the fact that this splice has failed on multiple vehicles indicates a better design is needed.
 
TickyT - interesting and yes, I agree, with why they did it (and thought it was a good idea) and the problems it can cause. At those current levels they should have connected the alternator lead, main +12 harness connection and battery to fusible link lead to a bolted distribution point (at the fusible link black housing). Someone wasn't thinking on that day...

My patrol has a fork right at the fusible link that goes to the alternator and to the main vehicle feed. But then it also (old school) has a remote sense for the regulator right to the battery too.

cheers,
george.
 
Everything is normal now cell lights up.

The alternator was putting out 14-17 volts but was only getting 11.0 back. The battery and fuse box was only getting 11.3. Replaced the wire connector and nut no issues.
 
Fusible links connect DIRECTLY to the Positive of the Battery - right at the post. They are the 'thin' wires versus the heavier starter motor wire.

They look like in the picture, though I have moved the connector etc into the battery housing area - stock connectors sit on the engine side of the housing.

flinks1.jpg


cheers,
george.
Wow .this exact problem happen to me driving to work yesterday morning.luckily I was a few blocks away from the shop so I was able to get it there.today I popped the hood after reading this thread ,moved around the wires you have pictured here and heard like if my doors unlocked.I got in and she fired right up!my wires also hang outside the battery box,seem to be pinched.need to replace them. Thanks for the info guys!
 
Back
Top Bottom